Amateur Engine Removal Pt#2

TurboManiacal

Donating Member
No pics. Dropped the camera last time and lens won't entend out...(fuck).

So I finally made it back into the shop and started moving parts from one engine over to the new one. Here are the lessons learned for today:

1) Need a new distibutor...old one is rusted beyond recognition. Don't store engine without Cap on the rotor.

2) Don't try to catch a falling tool box loaded with tools. It cuts the shit out of your fingers.

3) My tools no longer are in order. 152 Wrench pick up is no fun.

4) Myclone is good at filling orifices. The engine he prepped for shipment for me was incredibly prepped. Everything was sealed with tape or was capped in some way.

My only question right now:

Gonna go for a bolt in tommorrow. Hopefully things will go well, need to know about sealing the new intake, what color silicone do I use? Red / Blue? Any idea what I'm talking about? That's all they had at the shop.

oops dinner is ready...I'll be back in a bit to type more.
 

TurboManiacal

Donating Member
Okay...In a few hours I'll be back in the mix. Hopefully I'll be able to make significant progress today. We'll try at least.

I've been mulling over this distributor problem I have. The one that I had got severly rusted and I don't think that it's any good anymore. So here are my options as I see it:

1) MSD billet dist for $290

or

2) Reman w/ Delco pack for ~ $125.

I'm not looking to do things on the cheap...I'm willing to spend the money now as opposed to later. I'm leaning towards the MSD as I've never really heard anything bad about the new dist yet. thoughts?

Next question: I'm pulling multiple sensors our and items that screw into the heads & intake that I can only assume tap into the coolant flow. When I'm reinstalling these...do I need to teflon the threads?
 

myclone

Donating Member
Glad you liked my orfice filling cabability.... and I only thought E appreciated it. :lol:

Seriously, there should have been a caulking gun and tube of sealant in the bottom of the crate in plastic. Thats for sealing the ends of the intake. I also included two little brown bottles of gasket shelack(sp?) just for the sensor sealing issues. Just unscrew the cap and there is a brush attached to the underside of it for applying it to the threads.

All that stuff along with the motor mounts and heat sheilds was wrapped in plastic and tucked under the engine when I crated it up. You didnt throw all that away did ya?? :eek:
 

TurboManiacal

Donating Member
Dave,

today I found the calking gun w/ the right stuff you mentioned. Used that when put the intake on. Thanks!

As to the intake bolts: I coated the threads (with finger) with the right stuff and hand tightened them today. The online manual my shop has didn't mention a torquing order so for the moment till I can get back into the shop, the intake is just handtight and I'll properly torque them down later:

Next round of questions:

- Do I need to remove the upper intake to torque them down? I'd kinda been hoping to avoid that but it's no biggie if I do.

- What is the sensor that is immediately to the left of the Thermostat? Mines busted and I need a replacement.

- I used teflon on the knock sensor and other water jacket fittings. Is this okay?

It's going to be till next monday / tuesday till I can get back in the shop...so I think the wife gave me the go ahead on the MSD Billet distributor...any last words before I wed Summit w/ my CC #?
 

Loeryder

New member
Knock sensor just threads into an empty cavity and should not get tef tape
it can deaden the sensitivity of the sensor.
Also dont torque it down too tough like 14 lb/ft i think.

That sensor next to the thermostat is the coolant temp sensor for the ECM.
 

myclone

Donating Member
Couple of things..

Ditto on the tefllon tape on the knock sensor. Thats a no no.

Since you used the right stuff on the intake bolts and only finger tightened them you will need to remove them now. That sealant sets up FAST and when you tighten the intake bolts down with a wrench later you'll just break the seal. You need to remove them, use a wire wheel or wire brush to clean the sealant off, coat the threads with gasket shelack, and finally reinstall them to their proper torque (sorry, I dunno what ftlb rating they are sposed to be torqued to as Ive installed enough of em I can do it by feel).

Ya really should have waited on applying sealant to the ends of the intake too as that sealant has set up by now also. You might be ok and not have any leaks but I cant promise it. Best scenario would be to yank the intake and clean the sealant off the ends of it and the block then apply fresh sealant then put ithe intake back on and torque it down.

(noobs :roll: )





Sorry, couldnt resist.... :D
 

TurboManiacal

Donating Member
myclone said:

Oh yeah? Could you design a theater wide Army Communications network incorporating tactical and strategic comms from Fort to Port and Port to Assembly Area and into the AOR w/ straight Digital Data and Voice Radio architecture?

Fuck...I had that intake clean...I mean I spent time on that bish yesterday...I wonder if I can get lucky and just get the bolts out...fuck.

You still didn't answer my question on removing upper intake.
 

CavScout

Member
Oh yeah? Could you design a theater wide Army Communications network incorporating tactical and strategic comms from Fort to Port and Port to Assembly Area and into the AOR w/ straight Digital Data and Voice Radio architecture?

DAMN...It's all I can do to set a Sincgar for freq. hop. You are the man, Sig.

I got the intake order (sorry, no pics): Starting from the two middle bolts, working outward on each side, tighten to 18 ft/lbs. (24 Nm in case they are using Metric).

HTH. (hua?)
 

myclone

Donating Member
Sigo said:
myclone said:

Oh yeah? Could you design a theater wide Army Communications network incorporating tactical and strategic comms from Fort to Port and Port to Assembly Area and into the AOR w/ straight Digital Data and Voice Radio architecture?

No, but I know not to put sealant on fasteners then come back a few days later and tighten em down. :p :p . Relax, its no big deal really just some extra time.

Fuck...I had that intake clean...I mean I spent time on that bish yesterday...I wonder if I can get lucky and just get the bolts out...fuck.

You still didn't answer my question on removing upper intake.

You can bolt it on with the upper in place.. Heres the catch though. I dont think you can get a torque wrench on em to torque em to spec with the upper on. So, ya got two choices. Leave the upper on and tighten the bolts with a wrench to a torque value of "good nuff".....or yank the upper so you can get a socket/torque wrench on the bolts to appease the engineers in the crowd. Myself? I can do it without a torque wrench just cause I can and it pisses off the engineers but that dont help you half a world away.
 

myclone

Donating Member
Oh yeah... Im pretty sure I put a new upper/lower syty intake gasket in your bag-o-goodies that the sealant was in. Whatd you do uncrate the engine and forget about the extra goodie bag?? :-?
 

TurboManiacal

Donating Member
myclone said:
Oh yeah... Im pretty sure I put a new upper/lower syty intake gasket in your bag-o-goodies that the sealant was in. Whatd you do uncrate the engine and forget about the extra goodie bag?? :-?

dave,

your bag of goodies was incredible. Yes, I have the intake gasket. I just didn't want to go through the hassle of dealing with it. Fuck it is what I'm about to say, I'm going to rip that bish apart and get the upper & lower intakes matched. If I'm pulling that intake apart then I'm doing it the right way. Almost want to put the rebuild on hold so that I can have the intakes polished too.
 

myclone

Donating Member
Unbolting the upper from the lower and reinstalling it is easy since you got the gasket. Might take ya 10 minutes. If you really wanna port the upper lower then to do it right is gonna take some hours (thats one reason I havent ported mine yet). Thats up to you though. If it was me and I was going back stock like you I might knock down some obvious mismatches slightly just to make me feel better but other than that Id leave it alone. The heads are the biggest bottle neck IMO and doing anything with those would require their removal and lotsa time with the die grinder to make any worth while improvement.
 

TurboManiacal

Donating Member
I guess I need to clarify for everybody here what my goals in Life are...

lets see....

1) Get Married (done)
2) Have sex (tied to #1)
3) Own Lamborghini Diablo (won't happen)
4) Own Syclone (got it)
5) Jump out of airplanes (done that, broke 2 feet)
6) Go to Germany (done)

7) Own an unbreakable 12.0 Syclone.

Seeing as how #7 is the only one that is relevant here, I'd like to do this buildup right. I'm not going back to stock...I'm just doing the economy replacement right now. Cause this old block is getting the royal treatment in buildup. I won't finish building it in the next two years but that's fine. The next time I take the syclone off the road it'll come off for the complete package. I won't piece meal this.
 

myclone

Donating Member
Add two more things to your list.

1. Find bintowlhead and kick his ass right before you cap him.
2, Ditto for sodamninsane,

Personally Id be happy with an unbreakable 14 second syclone myself..... wait, no I wouldnt.
 

TurboManiacal

Donating Member
CavScout said:
Oh yeah? Could you design a theater wide Army Communications network incorporating tactical and strategic comms from Fort to Port and Port to Assembly Area and into the AOR w/ straight Digital Data and Voice Radio architecture?

DAMN...It's all I can do to set a Sincgar for freq. hop. You are the man, Sig.

I got the intake order (sorry, no pics): Starting from the two middle bolts, working outward on each side, tighten to 18 ft/lbs. (24 Nm in case they are using Metric).

HTH. (hua?)

Okay this is wrong from what I've seen. I've got the printout on the motor and it says 36lbs but it does not specify an order...but to be safe I was going to use the same pattern that you said to use.
 

CavScout

Member
Wait...Did you want Intake or Head patterns?

I gave the Intake (lower). Heads would be better done with a pic, but I'll try to print one out. Or I could try to draw one, but I'm just a dumb scout and can only draw "Sand tables". :wink:

EDIT: Nope, you're right. I looked up intake, but gave you the upper intake torque. Lower should be 35 ft/lbs in this book. Shame on me.
 

TurboManiacal

Donating Member
CavScout,

I thank for your concern and diligence in providing me the correct answer. Your devotion is duly noted and will be taken into consideration during the next syty.net perforance evaluations.
 
Top