an fittings direct

BMFB

Not to scale
I'm looking to buy some an fittings and some steel line. I don't like the idea of running a teflon coated rubber hose covered in a braided exterior, For some reason I picture it breaking off... anyway I see there is a place called anfittingsdirect.com that sells a product that says its better suited to E-85 and meth, and I was wondering if anyone here had ever ehard of them. Its cheaper but about half, but I can't find anything about it other than their fittings are the only ones that will work with their line...

any input?
 

nallj92

Active member
Re: an fittings direct

PTFE is a hard plastic line like stock GM clip on fuel lines.

thier fuel lines are teflon, but they are not graphite impregnated( good for other fluids) but for fuel lines you get static charges and the graphite impreganted PTFE lines are what is truely needed. ANfittingsdirect uses a ferrel/olive style AN fitting which is reserved for PTFE style lines.

i do have a source for PTFE with the graphite for a decent price that i have used. the fittings is where it does get expensive if you go the aeroquip route. I used the anfittings direct fittings on the different company's PTFE, it seemed to seal up ok, but i havent ran the car yet, so i cant give it my full seal of approval.

http://www.jdaent.com/high-pressure-teflon.html


hth
 

Syclone22

Member
Re: an fittings direct

:roll::roll:
PTFE is a hard plastic line like stock GM clip on fuel lines.

thier fuel lines are teflon, but they are not graphite impregnated( good for other fluids) but for fuel lines you get static charges and the graphite impreganted PTFE lines are what is truely needed. ANfittingsdirect uses a ferrel/olive style AN fitting which is reserved for PTFE style lines.

i do have a source for PTFE with the graphite for a decent price that i have used. the fittings is where it does get expensive if you go the aeroquip route. I used the anfittings direct fittings on the different company's PTFE, it seemed to seal up ok, but i havent ran the car yet, so i cant give it my full seal of approval.

http://www.jdaent.com/high-pressure-teflon.html

So if i am correct teflon liner fuel lines are better
for exotic fuels ??? :roll:
 

BMFB

Not to scale
Re: an fittings direct

I know that teflon is better when the fuel can eat the rubber lines
 

e95 Ty

New member
Re: an fittings direct

The teflon can not "come off" it is manufactured into the lines.....These lines have been proven over and over again. If steel braided lines are good enough for NASCAR and NHRA and IHRA top fuel dragsters that run nitro I think they are safe for you also. If you do want to go with just stainless steel tubing though, I had a catalog sent to me recently with all the tubing and fittings you would need. I will look for it today.
 

nallj92

Active member
Re: an fittings direct

another common problem of rubber base braided lines is that the fuel permeates the rubber and you can get a fuel smell coming out of the braided lines after sitting for a while (over winter). It is all to common for rubber braided to break down after a while and even crack/leak if in service for 5 year plus. Teflon solves this issue and is the main choice of fuel lines today but OEM's next to solid lines.

Downside is its more expensive, but then you have the ability to run any type of fuel/oil etc, and have lines that last over the lifetime of the vehicle.
 

BMFB

Not to scale
Re: an fittings direct

Well alright, o was mistaken about how the lines were made. Does anyone know anything about the type of line that an fittings direct is selling?
 

MadMike

Member
Re: an fittings direct

Thats where I got mine. Your get what you pay for. They take a min to ship like 3days.

And I had some issues with them sending me some tube that was undersized, it was REALLY tough to get the ends in the line. But it only happened once. Also some of the fitting failed when i went to take them off, kinda why you have them for the easy on/off. The pipe on the fitting twisted bc the nut gawled up where it was supposed to turn.

Also they didnt like to seal up without cranking down on them more than I liked. I worked as a millwright and machinst for years but maybe I'm new to the AN stuff. But the Aeroquip stuff was way nicer.

That said for a third of the price, I've made it work and kept ordering. have used like over $1000 worth. Think I have pics of it in use on my injection setup. They are in my first post My understanding is that once you go with one brand you really cant intermix the hose and ends.

There hose is PTFE,generic Teflon, with stainless braided wrap. Fittings aluminum.
 

BMFB

Not to scale
Re: an fittings direct

interesting...for a third of the price I might be willing to make them work as well...
 
Top