ANS Booster Controller

ZR1TR

New member
Recently bought a 93 Ty and it had one of these connected to the boost solenoid. I am trying to get the truck tuned up and running right. I have since disconnected it and plugged back in the stock connector and boost has been more erratic than ever. Is it still a good mod or just old technology?
 

ZR1TR

New member
Re: ANS Booster Controller

No one has any experience with this? I've only been part of the community for a short time. If this has been discussed before I'd appreciate a link otherwise I think you guys want me to blow it it so you can pick it up cheap! Seems to me that's how this board works! You guys kill the value of these trucks!
 

sytyguy

Moderated User
Re: ANS Booster Controller

Nice way to start out....busting the community's ass because no one responded to your post within 3.5 hours....on a Sunday....in the middle of football season. How about you show a little respect when looking for help?

Now, because I DON'T want to see a truck blown up....how about you provide some more details?
What chip?
What turbo?
What wastegate?
What exhaust?
How are the boost solenoid vac lines hooked up?
Any vac leaks?
Any datalogging capabilities?
If so, any datalogs?
What is your definition of erratic?
 

ZR1TR

New member
Re: ANS Booster Controller

Nice way to start out....busting the community's ass because no one responded to your post within 3.5 hours....on a Sunday....in the middle of football season. How about you show a little respect when looking for help?

Now, because I DON'T want to see a truck blown up....how about you provide some more details?
What chip?
What turbo?
What wastegate?
What exhaust?
How are the boost solenoid vac lines hooked up?
Any vac leaks?
Any datalogging capabilities?
If so, any datalogs?
What is your definition of erratic?

Well my point exactly! I had to ruffle feathers to get a response! I'm not 16, this isn't my first rodeo and I do t expect to run 12s out of the box. I want to do things right and all I'm doing is asking for help.
 

sytyguy

Moderated User
Re: ANS Booster Controller

Well my point exactly! I had to ruffle feathers to get a response! I'm not 16, this isn't my first rodeo and I do t expect to run 12s out of the box. I want to do things right and all I'm doing is asking for help.
You don't have to do sh*t on here to get a response except wait.....which is exactly what you did. What you didn't do is show respect, so consider my reply a courtesy that won't be extended again if you ask other questions with the same attitude. We are a small community working on trucks that are 19-21 years old and have had nearly all questions about them asked and answered. We have a lot better stuff to do than deal with people who come on here demanding answers to questions without showing some respect. You're asking us to provide a service for FREE on a weekend......go ruffle feathers elsewhere.....we respond to courtesy and respect.
 

"Nickel"

S-Series Syco
Re: ANS Booster Controller

Advice, stop getting snippy, or you'll get shit on and get 0% help and most likely banned.:2cents:
 

ZR1TR

New member
Re: ANS Booster Controller

I didn't ask who killed Kennedy, just whether the ans controller was still a viable boost controller. I will say Tom at sportmachines was very gracious and on a phone conversation was very nice and non assuming. Wish his shop was closer to TX.
 

ZR1TR

New member
Re: ANS Booster Controller

I didn't ask who killed Kennedy, just whether the ans controller was still a viable boost controller. I will say Tom at sportmachines was very gracious and on a phone conversation was very nice and non assuming. Wish his shop was closer to TX.

Look at what the new member gets "I'm new and a glove to the mouth." I've searched ans boost controller with quotes and every special character i could think of and nothing."
 

sytyguy

Moderated User
Re: ANS Booster Controller

Sportmachines is always nice....no surprise there.

Do you not understand why I'm responding the way I am? Have you reread your posts? Your original post is not the issue....it's the fact that you waited 3 hours and 24 minutes and when not given a response (again, on a Sunday afternoon), you resort to calling us out as the driving force behind dropping the value of these trucks because we all scheme together to not answer questions so you'll blow your truck up and have to sell it cheap. No one is forcing you to press the gas pedal. Got crappy boost control? Don't get into boost until you get the problem fixed. If anyone blows up their truck because they didn't get an answer to a question, it's THEIR fault, not ours.

Fact is, you own one of these trucks and judging by your questions, you may need our help in the future. My replies are advice to help you get the most out of your future questions. Again, we respond to respect. not demands or insults.
 

JAY

Donating Member
Re: ANS Booster Controller

Good info here: http://www.syty.net/forums/showthread.php?t=83163
http://www.syty.org/old/modlist.html

Search can be your friend. :)

ANS BOOST CONTROLLER To run boost levels higher than the stock 14psi an additional boost controller is required. The ANS boost controllers simple wiring, use of the stock wastegate solenoid and low cost (Around $200) has proved it to be the best choice for most applications. The lack of boost level feedback into the controller means that boost creep and over-boost can occur on some trucks (Depending on turbo wastegate condition, exhaust and other variables).
The turbo boost level is controlled via a little solenoid that sits on top of the turbo in the middle of a hose that runs from the turbo to the wastegate. The solenoid acts as a bleeder valve to create a small leak in that hose, so the wastegate won't see all of the boost pressure that the turbo is generating. That solenoid is normally open, so that if it fails, you will only get about 10 psi max boost [8 psi is where the wastegate starts to open]. When the truck is on, there is 12V running to that solenoid and a ground wire running back to the ECM which then switches the ground rapidly to pulse modulate the solenoid (i.e. open and close it really fast to leak-off the flow of boost pressure to the wastegate actuator).

The ECM monitors the boost via the Manifold Absolute Pressure (MAP) sensor. The ECM also has a table that indicates the desired max boost for a given RPM. When boost approaches max, the ECM will look in another table to see just how fast to modulate the solenoid. If the table indicates n-percent, the ECM will ground the solenoid wire n-percent of the time to cause it to close and leak-off n-percent of the boost pressure going to the wastegate. Spikes can occur if that n-percent isn't enough to open the wastegate far enough to control the boost.

The ANS controller is simply a device that will allow the driver to control that n-percent. The knob controls a 555 timer chip which is used to pulse-modulate the solenoid ground signal anywhere from open almost all the time (minimum boost) to switching so fast that it's almost closed all the time (More boost than you want to dream about).

Installing an ANS controller is quite easy. Since the plug that goes into the solenoid has 12V when the truck is on, that is where the power comes from. The stock solenoid plug is unlatched, the ANS plug inserted into to the solenoid, the stock plug is inserted into the socket on the ANS wiring and wire is bolted to a nearby ground source. The cable to the controller is run along the firewall, through a grommet then up to the dash facia.

There are two switches on the controller along with a boost level knob. One switch says "On" and "Off." In the Off position, the solenoid will not be modulated and only generates about 10 psi of boost - just the same as if the cable was unplugged on the solenoid. In the "On" position, the other switch comes into play. The other switch says "ECM" and "TC." The "ECM" will let the ECM control the boost as it normally does; it simply connects the ground wire that was on the solenoid back to the solenoid. The "TC" lets the knob control the solenoid's on/off rate. A small LED flashes to indicate the rate at which the solenoid is being pulsed.

It is VERY important to keep an eye on the boost. The knob on the controller cannot be set for 17 psi one day and have it always at 17 psi. Also, because the ECM does not have control of the boost level it cannot back-off the boost if it hears detonation

The ANS is a neat gizmo for the Sy/Ty: Its a plug-in controller with very little installation hassles; Unlike N2O it is relatively safe to use on a stock engine; It's a lot more convenient than a bleeder valve under the hood that you have to jump out of the vehicle and adjust each time.
 

ZR1TR

New member
Re: ANS Booster Controller

JAY thank you for your input. I didn't mean to cause trouble but respect is a 2 way street. I joined this forum because I respect the members here. If I came off any other way I apologize. In my newbie post I mentioned the ans boost controller so I wasn't trying to be impatient just exited
 
Top