Atlanta area tuning

LowLife

New member
Re: Atlanta area tuning

ndburli - I'm not Hood.....but a stock chip reflashed should be enough until you're ready to do some more mods....I believe Hood's reflash gives you a few extra pounds of boost while changing fuel curves as well.
 

ndburli

New member
Re: Atlanta area tuning

Thanks dude! That is he way I will go for now then. Last question...where is said 2 bar chip found? Tha is for all the help!
 

ndburli

New member
Re: Atlanta area tuning

So I have removed the module from under the dash...where does the chip sit in the module? Do I need to unplug all the connectors on the module to get to the chip?
 

sytyguy

Moderated User
Re: Atlanta area tuning

2 1/4" screws hold a cover plate on. Remove that and pop the EPROM (blue cover with 2 visibility holes) out like a stick of RAM (two plastic retaining clips....one on each end).
 

ndburli

New member
Re: Atlanta area tuning

Well sweet deal...I've got her out.
ndburliso


Now I just need to mail this in to you correct? and do you only accept paypal on the website?
 

sytyguy

Moderated User
Re: Atlanta area tuning

Paypal or CC. I'll send you a Paypal request tonight for $57 and you can pay either way (to pay with CC, click the "Don't Have a Paypal Account...." link instead of logging in).
 

ndburli

New member
Re: Atlanta area tuning

Payment done...I will ship it out tomorrow. Any idea when I might have it back? I am thinking Wednesday-Thursday of next week with the Holiday coming up. Sound about right?
 

sytyguy

Moderated User
Re: Atlanta area tuning

Payment done...I will ship it out tomorrow. Any idea when I might have it back? I am thinking Wednesday-Thursday of next week with the Holiday coming up. Sound about right?
I'll either get it Saturday or Tuesday. Either way, it will go back out to you Tuesday and you should get it Wednesday. :tup:
 

ndburli

New member
Re: Atlanta area tuning

Hey Michael...I sent the 2 bar chip in to you...I checked my tracking and you should have it today or tomorrow. Not sure why FedEx is taking so long but either way you will have it at the latest tomorrow.

thanks!

Nate
 

sytyguy

Moderated User
Re: Atlanta area tuning

Got it today, reburnt it today, and reshipped it out to you 5 min ago.
 

ndburli

New member
Re: Atlanta area tuning

Just had a thought...is it a plug and play or will I need additional tuning? Also...if I decide to do EGR delete, additional ic pump, etc...would it then require additional reprogramming? I guess I am trying to figure out at what point the 2 bar is no longer useful to me and a 3 bar chip/map would be necessary. Thanks again for all the help!
 

sytyguy

Moderated User
Re: Atlanta area tuning

Ignore me. As soon as I typed that reply, I realized the chip I reburnt today came from USPS, double checked and sure enough, it went to Texas. My bad and sorry for the false hopes. Will be on the lookout for yours tomorrow.

About the chip.....it is plug-n-play, but no chip is capable of growing with your mods. There is some flexibility in the burn, but if you modify something, technically, you could benefit from a retune. I usually advise customers to complete a substantial amount of mods before reburning (unless one mod necessitates a reburn, e.g. Meth injection, bigger injectors, 3 bar MAP, etc...). Then send the chip back for a full retune.

All things being the same, the only difference between a 2bar chip and a 3bar one is that the latter supports a 3bar MAP sensor. Now having said that, not many people go to 3bar unless they desire to turn up the boost, so you will usually gain something from going 3bar, but that's from running higher boost, not from the tune. 15 psi and below, 2bar and 3bar chips are the same.....both can accommodate more timing, more fuel, bigger injectors, bigger turbos, cams, alky/meth, EGR delete, etc...

The chip is currently setup to turn the IC pump on at 19 degC (66 degF), so essentially, the pump will come on with the key. On cold mornings, the engine will need to get above 66 degF to turn on the pump, but even at the dragstrip on a winter night, the coolant will be > 66 degF by the time you stage. So, think of the pump as hardwired. EGR is currently removed & the CEL is disabled, 1st boost limiter is removed, idle is improved, timing and fuel maps are redone to provide better acceleration & driveability, Speed and Boost limiters are raised (192mph and 16 psi respectively), WG control is optimized, and WOT performance is enhanced with more timing and more accurate fuel delivery.
 

ndburli

New member
Re: Atlanta area tuning

Bummer! Its all good though...I think FedEx is scheduled to deliver it tomorrow. As for all the perks...sounds like it is really going to be a good thing. I am assuming I will still need to actually delete the EGR with the kit correct? And as for timing....I am still not clear on the difference between the "chip timing being advanced" versus mechanically setting the time on the engine. Maybe in time the "Noobness" will wear off and my eyes will see the light....until then I will absorb as much as possible!
 

sytyguy

Moderated User
Re: Atlanta area tuning

Bummer! Its all good though...I think FedEx is scheduled to deliver it tomorrow. As for all the perks...sounds like it is really going to be a good thing. I am assuming I will still need to actually delete the EGR with the kit correct? And as for timing....I am still not clear on the difference between the "chip timing being advanced" versus mechanically setting the time on the engine. Maybe in time the "Noobness" will wear off and my eyes will see the light....until then I will absorb as much as possible!
What'ya wanna know about mechanical vs computer-controlled timing?

Essentially, when we program in more timing in the chip, we add spark advance in certain where it's beneficial. For cranking, less advance is needed, but some engines idle better with more advance, so we have to pull a little bit of timing out during cranking scenarios and add back some for idle areas (usually around 26 deg at 800 rpm / 40 kpa). Same goes for other areas. You can get better economy by adding a little bit of timing and pulling a little bit of fuel out at cruise. Also, you can get better spool up with a little extra timing and a little less fuel at low boost levels, but you have to decrement the advance accordingly to boost (in a semi-linear fashion) to avoid spark knock at WOT.

The goal of all spark timing is to get the fuel to ignite at the optimal time (usually right near the end of the compression stroke - hence why advance is listed as BTDC). If nothing affected the burn rate and ignition point of fuel in an engine, then we could set a mechanical advance and be done. However, the reality is that lots of things affect the point of ignition: RPM, air temperature, AFR, octane fuel, boost pressure, etc... For instance, higher octane fuel burns slower than lower octane fuel. Knowing that, when running higher octane fuel, you can imagine that we'd want the spark plug to fire a little earlier in that cylinder to give the mixture time to ignite. Run too low octane fuel or too much advance and the mixture ignites prematurely and you have combustion trying to force down the piston while the crank is still trying to force it up to TDC. This is pre-ignition/detonation/knock.

The ideal situation would be to run as low octane fuel as possible without detonation. However, on pump gas, this often results in a compromise of less boost or less advance or both. This is why you can run much higher advance on race gas, it needs the extra time to burn and generally burns cooler allowing more advance and more boost. On that note, as tempting as it is to just throw a ton of timing into a tune (either electronically or mechanically), the better trade-off has always been to run more boost instead. This is where the benefit of a 3bar burn comes in. :D
 

sytyguy

Moderated User
Re: Atlanta area tuning

I cannot recall where I read this tid-bit, so I can't quote the source, but each engine has a mathematically-optimal point where spark should occur. It is computed based on stroke length and rod ratio. The BBC is 34ºBTDC, and the SBC is 38ºBTDC, IIRC.

If detonation occurs before this timing is reached, the CR must be reduced, or octane increased. If detonation does not occur, CR can be increased (for power gain), or octane reduced (for cost reduction). But the ratios don't change. In real life we add more timing to take advantage of the available octane overhead, or decrease timing which is easier and more expedient than mechanical engine changes and octane changes.

Any comment?
Sure that wasn't optimal point for peak cylinder pressure (PCP)? I can't imagine that there is a mathematically perfect point for spark for something as variable ridden as 4 stroke engine. Just changing the AFR (thus changing the speed of the flame front) changes the optimum point of ignition in order to achieve peak cylinder pressure.....and that's just one variable. Throw in cylinder pressure, piston type, cylinder head efficiency, RPM, CR, spark plug placement/angle, octane, temperature, and engine load and you'd fill 10 chalkboards coming up with a universal formula.

I could see PCP being a constant (10-20 deg ATDC is usually accepted, but you'd still need some specs to get it perfect), but point of ignition is so dependent on the factors that drive the combustion itself, that I personally cannot see there being a constant for it.

But I've been VERY wrong before.
DaveP said:
Here's another thought on timing that came up this morning while reading Don W's post about his finding 3 MPH of trap speed (power increase) by leaning his mixture. He mentioned timing in passing, in that he retards if KR (his main indicator) is logged.

Engines can't tolerate as much timing in the higher gears as they can in lower gears at the same RPM because the chamber pressures have more time to stabilize at higher temperatures. Long before electronic-controlled advance curves were available, some drag racers used a dual pick-up distributor where the second pick-up was retarded several degrees from the primary. A simple switch on the Lenco shifter switched the pick-ups to the retarded one when shifted into high. Trap speeds improved.

It would certainly be very easy to fit a 3rd Gear switch to the valve body to indicate the transmission is in third to facilitate this timing retard. But I have no idea if such an input (correction) could be incorporated into the timing tables or code. Just a thought.
This would be a very neat idea. I actually tune timing for boost in 3rd gear so that I'm seeing a heavy load. I might give up some advance in 1st/2nd, but I err on the side of safety by tuning in 3rd. WOT in 4th is rarely seen by most and if so, for very little time. The easiest way would be to create a table to add some retard based on MPH. That way you're not rewriting the whole F1 table and then adding advance with a separate table (a la F80). Then you could do the math on when you logically hit 3rd gear and throw some retard in for the kpa/rpm cells you desire.

Neat idea, Dave.
 

sytyguy

Moderated User
Re: Atlanta area tuning

Nathan, Fedex just dropped off your chip (just after the Post Office closed). I got it reburnt, boxed up and labeled, but it won't hit the road until tomorrow, so you'll get it Friday.

USPS 9405 5036 9930 0128 2792 95
 

ndburli

New member
Re: Atlanta area tuning

Hey Hood...got a quick question. If I decide to remove my catalytic converter will the re flashed chip account for the additional flow or do I still have a potential for over boosting due to the stock waste gate?

Thanks,
 
Top