boost back pressure measure

IGottaSy

Active member
Is anybody measuring/logging boost back pressure? Care to share, pics? Where did you tap into? Etc. , etc.
So, I read that there is a problem anytime the combo makes more than 2:1 ratio back pressure vs boost. Cheap set up would be just a gauge with a check valve. Better set up probably a 4-5 bar MAP and datalog.
 

Don W.

Stab it and steer it
Re: boost back pressure measure

Quite a few measure it. Doesn't seem popular around here. Tap into the exhaust near the turbo inlet. Jury-rig some metal tubing to get away from the heat and measure away. I've heard 1:1 boost to back-pressure. No clue if that's accurate. Check valve? For what may I ask?

The turbo is by definition a restriction. We "use" that restriction to, in effect, generate the power to spin the compressor wheel and make boost. The tradeoffs are many. Backpressur to boost "ratio," turbo efficiency, Intake and exhaust plumbing efficiency throughout the system. Just a few that come to mind.

It's my opinion that most of us here are ceder-yourpaz engineers. Including me. I would thoroughly enjoy talking to a true turbocharged internal combustion engine engineer. GM, Ford, whatever. I could probably wear him/her out with questions. :rotf:
 

It's just a six

Super Member
Re: boost back pressure measure

This is what Rick Head sent to me in an email about my friends 36 Chevy truck w/a 292 inline six.

"On your friends truck, 31 psi back pressure at 21 psi boost is not bad. Back pressure becomes a problem when the differential causes reversion (soot) in the intake, doesn't want to RPM or make anymore boost basically slows everything down and becomes a restriction. Cool Videos cool truck!"
https://www.youtube.com/watch?v=QslZvPAYkGM

https://www.youtube.com/watch?v=WjQ7PmXSKcw

https://www.youtube.com/watch?v=Vk-AJEkkR9I
 

qbnkiller

Conflaguration Specialist
Re: boost back pressure measure

Backpressure is good to monitor, along with othet bits of information. If analysed properly, it can help to maximise a combo.

In street applications, you want a little bit of Backpressure. This helps to get the turbo lit faster. When designing a systrm, I am looking to have it under 2:1 - nice if its 1.5:1. Beyond that, you may run into shaft speed issues.

Its a bit more complicated than that...this is a thumbnail sketch. I have spent some time with turbos and a gas stand dyno for turbos. I have seen some common myths disspelled, and havhalearned quite a bit that I have carried out to actual customers vehicles. Like most things on a public forum, most is heresay or unverified via scientific testing (why did this make a difference). I have tried to find the cause and effect of these changes. It helps ensure a more positive and repeatable experience for customers.
 

IGottaSy

Active member
Re: boost back pressure measure

Check valve holds pressure so you can read max back pressure on a plain gauge. This would be rudimentary but it should work, tentatively. Those who have swapped to vortecs should have noticed this dramatic difference had they measured. It's just more useful information to complement the perfect combo. Cool to know. :)

Quite a few measure it. Doesn't seem popular around here. Tap into the exhaust near the turbo inlet. Jury-rig some metal tubing to get away from the heat and measure away. I've heard 1:1 boost to back-pressure. No clue if that's accurate. Check valve? For what may I ask?

The turbo is by definition a restriction. We "use" that restriction to, in effect, generate the power to spin the compressor wheel and make boost. The tradeoffs are many. Backpressur to boost "ratio," turbo efficiency, Intake and exhaust plumbing efficiency throughout the system. Just a few that come to mind.

It's my opinion that most of us here are ceder-yourpaz engineers. Including me. I would thoroughly enjoy talking to a true turbocharged internal combustion engine engineer. GM, Ford, whatever. I could probably wear him/her out with questions. :rotf:
 

IGottaSy

Active member
Re: boost back pressure measure

Thanx for the input!


Backpressure is good to monitor, along with othet bits of information. If analysed properly, it can help to maximise a combo.

In street applications, you want a little bit of Backpressure. This helps to get the turbo lit faster. When designing a systrm, I am looking to have it under 2:1 - nice if its 1.5:1. Beyond that, you may run into shaft speed issues.

Its a bit more complicated than that...this is a thumbnail sketch. I have spent some time with turbos and a gas stand dyno for turbos. I have seen some common myths disspelled, and havhalearned quite a bit that I have carried out to actual customers vehicles. Like most things on a public forum, most is heresay or unverified via scientific testing (why did this make a difference). I have tried to find the cause and effect of these changes. It helps ensure a more positive and repeatable experience for customers.
 

Darin

New member
Re: boost back pressure measure

Use a map sensor and log the voltages. You might get a better picture if a way could be figured out in data master to overlay the info, load vs rpm vp back pressure, etc.

Don't ask me how to do it, but it'd be cool.

Back to your regular scheduled program :)
 

Don W.

Stab it and steer it
Re: boost back pressure measure

Got it in the check valve. Should work if there are no leaks.
 

IGottaSy

Active member
Re: boost back pressure measure

Got it in the check valve. Should work if there are no leaks.


Don't forget to post vid or pics. A nice table would be helpful... U know, at say 10lbs boost, 15 lbs 18lbs, 20 lbs etc and post up!! :tup:
 
Top