Boost problem again

AXXE

Member
OK. Vacuum lines are good. Fuel pressure is right on. It got warm out and I went to the track. The truck made 13.5-14psi in 1st, 15-16 in 2nd, and went right to 18 in 3rd. Ultimate was on T1-18 and T2-18. Very little knock on T2 and none on T1. I adjusted the wastegate rod again today about 1/4 turn with no change. How far do I have to adjust it? It is really rusty and not easy to adjust.
 

RAACCR

Member
On 2002-03-16 16:00, AXXE wrote:
I adjusted the wastegate rod again today about 1/4 turn with no change. How far do I have to adjust it? It is really rusty and not easy to adjust.

You have to adjust the wastegate in 1/2 turn increments or else the hole won't match up with the pin. If it's rusty, spray it down with PB Blaster & let it sit overnight. Spray it again the next day, and break the nut loose before you remove the rod end from the wastegate pin. Once you've backed off the nut, remove the rod from the pin, and turn the end piece tighter...I'd recommend going in 1 turn increments. If it's rusty, be sure to hold the rod while turning the end piece so you don't damage the wastegate diaphram. Put the rod over the pin, then snug the nut against it. Repeat the process until your boost level is satisfactory & be sure to closely monitor knock while raising the boost.

HTH,
Rob
 

nick041881

Member
i gave the rod like 3 turns in my truck...maybe it was a little tight, but boost was rock solid and it didnt overboost.
give that puppy a few more turns...dont be afraid. you might also want to look at installing a large gate return type spring on the wastegate lever to help the actuator do its job. just my .2$
peace,
nick
 

Zac

New member
On 2002-03-17 02:25, nick041881 wrote:
you might also want to look at installing a large gate return type spring on the wastegate lever to help the actuator do its job.

Do you have any pictures of this? I am curious to see what it looks like. Thanks.
 

AXXE

Member
Thanks Nick. I think I need a few turns. I kept doing small increments and it is a pain taking everything apart every time. Do you have any pics of the spring setup? If not, where exactly did you hook it on? That sounds like a great idea.
 

Tooky

Serious about performance
I am wondering what you are doing that is taking so long each time to make it a "pain"? I take the wheelwell out and leave it out until days later when I'm good and postively sure that the WG is set where I want it.

Once the wheelwell is out I just pop off the bobby pin, screw the WG rod where I want it, put the bobby pin back on and go for a test drive around the block and note the results. Then I come home and do the same thing except with some gloves on to prevent burns. I can literally adjust the WG in less than 2 minutes, not a pain at all for me?
 

jwaller

Evil Genius/SyTy Guru
basically what nick was eluding to was a spring used for screen doors. you sinply leave the pin out of the WG actuator arm and insert the end of the spring there. its the poor man version of a stiffer WG spring. works pretty good. simply find a place to anchor the other end and your done.
 

Tooky

Serious about performance
What type of spring would you want to get? How can you measure the "weight" of the spring?
 

AXXE

Member
My WG rod is very rusted. even with blaster on it every day, it is not getting better. Thats the pain. I need a new, bigger turbo!
 

jwaller

Evil Genius/SyTy Guru
when you use an external spring you are really going at it on your own....so get something thats wound tight and isnt impossible to uncoil...and be careful!
 

nick041881

Member
i would buy several srings about 6 inches long or so with varying degrees of stiffness.start with the easiest and work your way up until your boost is solid. Like John said, be careful!! too stiff of a spring could hold your gate shut and boost could climb to dangerous levels.
good luck,
nick
 
Top