Brian , i need your advise.......

nightdiver

Active member
Brian i did some tuning and the Sy performs very well although my engine is very tired
I did a leak down test and i got #1 & #4 with 35 % loss and the others with 22 % loss
During tuning i desided to raise the advance because of the redused compression due to the loss
I am now running at 18 psi with 24* and no knock arround(no shit)
I really do afraid to add more but the MF needs it badly
Please advice how far should i go ? and where should i stop ?
Thanks
 

smeagol

Active member
Adding advance to make up for loss in compression isn't a good idea...

I find it hard to believe that you are running 18psi with 24 degrees of advance with no problems. What heads are you running? What plugs?
 

nightdiver

Active member
Well i got the heads with the truck when i bought it.
This was a KB truck so the heads are L35s with 2.02 & 1.6 valves
This is the first time that i use bosch spark plugs but i dont think that this made the difference
I got accel cap and rotor , taylor wires 50000 V coil & the old J&s ignition
The T 68 comes with 0.84 turbine and the 0.72 comp housing
It pulls like a Syclone :D
Those 18 psi runs where made with 130 * intake temp and 90* outside
I used 101 gas with 1 bottle of super 104 (makes big difference)im horny not stupid :wink:
So should i try 2 more * ?
 

smeagol

Active member
I didn't realize you were on a bit more octane.

With those heads, I wouldn't keep pushing the timing level. The goal is to keep timing to a minimum.

I'd keep timing low, and push the boost level if anything. What model of Bosch plugs are you using, and why? I've not heard of anyone in typical GM markets using Bosch plugs for high performance stuff. NGK, Autolite, AC are the faves usually. Not saying they won't work, but you know the story.

That's an awfully lot of timing for those heads. I did some tuning on those and we had like 14 or so, upped it a couple degrees and made gains, but past that, we saw no extra hp to speak of. Course that will change with the cam/octane/turbo etc etc... but I'm speaking in general.

Why do you feel it needs the timing so badly? You've verified the timing is accurate on the FAST, correct?
 

nightdiver

Active member
Ill do 21* to stay on the safe side
I used bosch cause i was waiting the cr42ts to arrive and i wanted to give it a try
I think it needs more * cause it pulls extremely well from 10 psi with 24* also. But then i could be wrong again since this is the first accurate tuning with any kind of aftermarket ecm i do :oops:
Yes the timing is right, i double checked it before the 10 psi and up runs
Ill go to a 4x4 dyno today and check the gains with advance but i wont go more than 20-22 since you say so
Ill start from 14* and go up
Ill give you the Bosch # later cause i dont have right now with me
 

smeagol

Active member
Well a dyno would help tell the story. Don't use my numbers as an absolute limit.. you may have something weird going on with the truck. Tune, see what the advance does for your power.. you may find you need 26 degrees with your combination... you may find anything over 18 degrees doesn't yield any gains. Keep checking the plugs for detonation, keep using good gas, and you'll do ok.
 

nightdiver

Active member
Cant buy experience

Cant buy experience

You are always right
Deto was there but the Fast didnt see it. Hows that ?
The j&s could see the deto easily.The Bosch Splugs are history now, two of them melted ,2 & 4
The fan at the dyno was a piece of shit although the dyno was brand new . I saw a maximum of 170 *F air intake temp.Thats 77*C
With this temp and the stock fan working we got 301 KW which is 409 engine Hp
This was a 19 psi run at 20* advance with a little :roll: detonation that i couldnt hear
Ill pull 2 or 3 deg.
This is fine if you consider how old is the engine
What do you think ?
 
Top