Can anyone help me out?

spooldup

Super Member
I just got my Ty back from getting a new motor in it and i was wondering if anyone could take a look at the datamaster file. One is when i am just crusin and the other i get on it floored. I was looking at a couple of things and the knocks where very high. When the scantoold at the mechanics was on it there was 0 knock. On the datamaster there was 200 at one point. The mecahnics test was while he was sitting still and mine i was driving, maybe thats why? I also noticed two flags, one with egr and one with something else. Also how do i load it on here so you can see it? Thanks guys for the help.

<font size=-1>[ This Message was edited by: 92 black typhoon on 2002-01-20 00:44 ]</font>
 

bdubb

I am teh kingpin!
dont feel like breaking in the motor a couple hundred miles, and a couple of oil changes.. just gonna get into it?
 

Buster

New member
On 2002-01-20 00:44, 92 black typhoon wrote:
I just got my Ty back from getting a new motor in it and i was wondering if anyone could take a look at the datamaster file. One is when i am just crusin and the other i get on it floored. I was looking at a couple of things and the knocks where very high. When the scantoold at the mechanics was on it there was 0 knock. On the datamaster there was 200 at one point. The mecahnics test was while he was sitting still and mine i was driving, maybe thats why? I also noticed two flags, one with egr and one with something else. Also how do i load it on here so you can see it? Thanks guys for the help.

<font size=-1>[ This Message was edited by: 92 black typhoon on 2002-01-20 00:44 ]</font>

Two hundred is pretty normal for a good running Syty, you need to look at knock retard, and not knock counts, should be displayed in degrees.
 

spooldup

Super Member
O ok. I am still reading the book. I will look at it again and see what the knock retard is. The motor that was put in has 48,000 on it so thats why i got on it.
 

JoeLutz

New member
Somebody with Datamaster experience please take a look at his files. He is maxing out at 15.5 degrees of knock retard and hes got a code 42. I don't have my book here to look it up, but I do know thats something to do with the EST.

_________________
Joe Lutz
4.3T > mc^2
Ty4redweb.jpg

communities.msn.com/joeelutz

<font size=-1>[ This Message was edited by: JoeLutz on 2002-01-22 21:43 ]</font>
 

spooldup

Super Member
I do know that the mechanic adjusted the timing. I asked him about the code 42 and he said that he just did not reset it after he was done.

I just looked at the file again. Why do i have soooo many error codes? I have codes, 12,13,14,15,21,22,23,24,25,31,32,33,34,35,42(we know of),43,44,45,51,53,55. What the F%&#@! I just spent $3,400 on a motor swap. Is this really bad? I have aftermarket parts like a turbo, chip and stuff but this scares me!

<font size=-1>[ This Message was edited by: 92 black typhoon on 2002-01-22 21:59 ]</font>
 

JoeLutz

New member
Did he disconnect the brown wire when he set the timing? Is your check engine light on? Does it work? I was reading here http://www.sportmachines.com/maintenance/aldl.html
You could have a bad ignition module. Most likely something is not hooked up right since the engine was just changed. How much do you trust the mechanic and how much do you think he knows specifically about syty's or about gm efi for that matter?
Your IATs were high too. Check the coolant in your intercooler.

You really need to find someone in your area with good knowledge of tuning sytys and have them look at your truck.

I would hate to see you blow that engine.

_________________
Joe Lutz
4.3T > mc^2
Ty4redweb.jpg

communities.msn.com/joeelutz

<font size=-1>[ This Message was edited by: JoeLutz on 2002-01-22 22:14 ]</font>
 

spooldup

Super Member
My check engine light does not work but it's funny you ask. The first day i got datamaster the truck was still in the shop. He came outside with me to watch me hook to the truck. I wanted to get a run in before the motor was swapped to be able to compare. When i tried it he said it won't sinc up because the check engine light was not on. Anyway it did but he told me that when he did it the check engine light was on. I have not seen a check engine light at all. The coolent in the intercooler is low and that will be corrected.
 

spooldup

Super Member
He does have a Grand national. I imagine he knows something but i do know he himself has never worked on a Ty. O, also there was this rigged looking wire that went to the fuel injector wire. He and i did not know what it was and he felt it was nothing so it was removed and placed aside. Someone before rigged the old motor in there along with chopping the harness. For what it was he did an amazing job.

<font size=-1>[ This Message was edited by: 92 black typhoon on 2002-01-22 22:23 ]</font>
 

JoeLutz

New member
IF the check engine light doesn't come on with the the switch on and engine not cranked, then either you got a bad ecm or most likely, someone has removed the bulb, because something was wrong causing it to come on and they had no idea how to fix it. If this guy has a GN and has a clue about tuning, tell him about the high knock retard. Try pulling the batt cable for a minute to reset the codes and then drive it arround easy to get it warm and datalog it again. The code 42 will probably still be there. Tell your mechanic about the code also and have him to fix the check engine light.
 
Top