can i use vortec shortblock??

supersports10

New member
i was just wondering if anybody has used a complete shortblock from a 96 and newer s10? With the stock heads, or L35 heads?

The reason i ask is because i can pick up a low mileage 2000 long block complete 4 250-300. I know that the pistons aren't the same, their higher compression. The vortec pistons are 9:21 compression and ours are like 8:3 to 8:6, but i do know that the sy/ty pistons are hyperutectic, and so are the 96 and newer vortec pistons.

Now i know the newer vortec heads are 64cc, but im not sure how many cc the older heads are. By looks i would believe them to be a larger cc, therefore lowering the compression below 9:0

So back to my question, do you think this would work and is there any other possible swapping issues?
 

Captain Morgan

Moderated User
people have done it, the major difference in the block design is of course the balance shaft (supposedly robs power), the crankshafts in the newer motors are lighter (and weaker) as a result of the balanceshaft, and then there are a handful of other little things, like the oil pan and I think the oil gallery and of course the timing cover and gears.

I cant really think of any "advantage" to going with a newer block, but if youre looking for any parts, I also have one sitting around in pieces.
 

supersports10

New member
thanks morgan, i know about the oil pan (i have a 4x4 newer pan under my bench.) and the timing cover and lifter retainer im familair with, ive had my 97 apart about a dozen times, and changed the motor already.
all the threads i see talk about the use of billet main caps, eagle rods, etc... etc.....

what im asking is if all the stock shortblock stuff will interface with the sy/ty topend??

also do you think this setup will take 15-20 psi?

the reason im doing this is i had my sy for 2 weeks, and i got happy with the wastegate rod, going from 11 psi when i got it, to 15 then 17 then
alot of white smoke (unburned oil) and a compression check revealed
#1--150
#2--100
#3--100
#4--30 :eek: :cry: :evil: :roll: :tdown:

i gave up after that.
 

sy538

New member
It was not the boost that killed you engine, it was knock. You don’t say how much boost you got up to when your engine died but I guessing it was about 20 psi that killed a 8.3 compression engine and you are asking if a ~9.0 compression will take 20 psi. I think it would with zero knock but I’m not sure you could do that even with 116 octane.

edit
Do you have a 3 bar map and chip?
 

PPI Typhoon

DIY Madman
I agree, knock is probably what happened to you. I'm running 23-26psi on a stock 130k mile motor with no knock and am running fine. If I had all sorts of knock.........say bye bye to the motor.

By the sounds of it, you want to be able to run faster than stock. I'd not waste your time with a higher compression motor. In the long run, you'll end up swapping it out because of the capabilities and strength of a built motor. Keep that 300 bucks, buy a motor from a junkyard and build up from there. If you were going for stock boost.......maybe, but you're worse off than a stock motor. With how much you'd spend in intercooler upgrades and maybe alky to be able to run that much boost at that compression.........you're looking at the cost to build a junkyard motor up with forged internals, which can handle much more.

just my :2cents:
 

supersports10

New member
sy538 said:
It was not the boost that killed you engine, it was knock. You don’t say how much boost you got up to when your engine died but I guessing it was about 20 psi that killed a 8.3 compression engine and you are asking if a ~9.0 compression will take 20 psi. I think it would with zero knock but I’m not sure you could do that even with 116 octane.

edit
Do you have a 3 bar map and chip?

yes i have the 3 bar map and the ultimate.i also have the pte 52, relocated ic hoses adjustable fp regulator, atr full exaust etc..etc....

and i know , i know the knock gremlin got me not the boost.

oh maybe it has something to do with the fact that i was running 93 in it plus octane boost for the first two tankfulls, then i forgot to put in the booster on the 3rd one, then oops!!

oh and i dont have a way of monitoring the knock yet.

the honey has a dell laptop, but i think its too new to have the right connector??? :D
 

PPI Typhoon

DIY Madman
supersports10 said:
sy538 said:
It was not the boost that killed you engine, it was knock. You don’t say how much boost you got up to when your engine died but I guessing it was about 20 psi that killed a 8.3 compression engine and you are asking if a ~9.0 compression will take 20 psi. I think it would with zero knock but I’m not sure you could do that even with 116 octane.

edit
Do you have a 3 bar map and chip?

yes i have the 3 bar map and the ultimate.i also have the pte 52, relocated ic hoses adjustable fp regulator, atr full exaust etc..etc....

and i know , i know the knock gremlin got me not the boost.

oh maybe it has something to do with the fact that i was running 93 in it plus octane boost for the first two tankfulls, then i forgot to put in the booster on the 3rd one, then oops!!

oh and i dont have a way of monitoring the knock yet.

the honey has a dell laptop, but i think its too new to have the right connector??? :D

I doubt that octane boost saved much of anything. Save your money and dont' buy that crap. If you want, just dump Xylene in your tank or invest in an alky setup. It will serve you much better in the long run.

As far as the laptop setup, you can use a serial to USB converter on most, if not all the cables that are out there and it should still work for you.
 

supersports10

New member
basically what im asking is is there any parts that wont interface with one another??

and then what is the life expectancy of the motor if i keep boost at 17 psi or less (provided i get a datamaster, and use it to keep knockk to a minimum)

p.s. i will be relocating the knock sensor to a better location when i change the mill.
:tup:
 

PPI Typhoon

DIY Madman
supersports10 said:
basically what im asking is is there any parts that wont interface with one another??

and then what is the life expectancy of the motor if i keep boost at 17 psi or less (provided i get a datamaster, and use it to keep knockk to a minimum)

p.s. i will be relocating the knock sensor to a better location when i change the mill.
:tup:

Your intake manifold will not bolt up to Vortec heads. You'll need to send that off to one of the various SyTy folks that can do that conversion for you.

The rest of everything should go right in.
 

supersports10

New member
Your intake manifold will not bolt up to Vortec heads. You'll need to send that off to one of the various SyTy folks that can do that conversion for you.

The rest of everything should go right in.[/quote]

i will be using stock sy heads, l35 heads,or a set of marine 4.3 heads that i have, off a 90 boat with less than 1000 hours on them.

thanks man i appreciate the info :tup:
 
Top