chip & boost control for new motor build?

ed hess

race or get outta the way
What am I upgrading to for a chip?

Almost done collecting parts for new motor. But I need to know what to use for a chip (upgrade of my stock ver 7 ultimate).

Do I just get the cam & heads version of ultimate?
Does this have boost control in it?

I realize that dfi with ramcharger boost control unit and wb02 is probably the best long term way to go.

But I need something to just get started with initially.

Learning how to do set up dfi would be nice to do at my leisure instead of doing it in a hurry to get my daily driver back on the road. And I have started to read about this.
Probably buy a beater when I do this. Also probably take up nolans offer on tuning if he does it with the setup I listed below.
Also i still havent found step by step instructions for building or buying a wb02 setup and how to interface this.

Setup purchased so far:
Crank sonny bryant even fire billet steel crank 4 bolt main splaid caps
Childs & albert c&a steel rods
Je pistons .30 over
412 comp cam w 1.6 rockers
cloyes roller chain & gears
Vortecs & intake (waller)
Pte60 w/ 3” dp (mike lee)
Atr jet coat headers
911 2800 stall (hartman)
msd 8367 dist
walbro fp & racetronix harness

need to buy yet:
was going to use 50# pte injectors.
Chip upgrade?
Boost control? (built into above)

Hoses
Water pump
New thermostat
Gaskets

As you can see I’m allmost ready here, (the big ticket stuff is bought)
I may have left something out.

Hopeing to get into the 11’s with this!

Ive been reading here for months but I still could use some help on what to use for chip and boost control initially before going to dfi?
 

BillC

New member
If you're willing to do some custom tuning, you could always start with one of BG's 50# chips and dial in the boost control yourself. Even if you have to buy a chip burner, an eraser and an editor (like Promgrammer), you'll still be way ahead of the cost of an aftermarket ECM. You wouldn't need to replace your Ultimate Chip, just reprogram the eprom on it.

Thanks to Dig's code hack, you can use a WB02 for tuning the chip very easily.
 

ed hess

race or get outta the way
bill

So if i use a 50# ultimate from bg, which chip are we talking about.

The 50# stock head version, or I thought he had a 50#head&cam version (no boost control on it)?

For boost control just use the old atr valve i have in a box someplace?

Sorry for the stupidity but if there isnt an off the shelf kinda version ultimate i can plug in..... then i think the transition to burning chips or learning dfi ....i might need some hand holding here.

I just havent been able to get a simple grasp of the subject from what ive read here on the board.

I can purchase a dfi ecm and all the stuff needed to use it from the guy i bought my block from. He wants 1k for that, but also comes with a lot of extras. Like turbo, 2 bov's mounted an a stock crossover pipe, xtra distributor, fuel cell, in bed ice box and valves for ic, larger throttle body, and i think theres some other suff. I can sell what i dont need.

So what basically are my choices here?


Wonder if i can learn the dfi stuff on the old motor. It cant be too involved making the physical changes for hardware. I would think someone has some settings for a stock set up and then the settings for dfi for a similar build as what i will have to just get started?

ed
 

ghettosled

SYTY SUPERSTORE
the ultimate chip upgrade for vortec heads/cam is pretty good. All the trucks we have installed them on run, idle, and perform great. of course you can't compare it to a stand alone or a custom programmed chip specifically for your build, but it does work quiet well for a *chip* I didnt see anything in your list which lifted a red flag.

the upgrade is $35 and either BG, or myself could send you the prom.
 

ed hess

race or get outta the way
mike

The "list" is pretty much what i have seen around here as kinda of like the "standard recipe". Figure it works for daily drivers wanting to visit the track a lot.

Does this upgrade have boost control in it?

35 bucks is a good inexpensive solution to the alternative.

Especially since i just want something that will allow the initail startup of the motor without confusing things or creating issues on initial startup.

Imagine if the new motor was started up with a newbie just getting started with dfi. That would would be a nitemare?


So last nite driving home I'm daydreaming about this problem - solution. Sitting at light and the guy next to me honks his horn. I look over and its the guy that has the dfi stuff that i bought the bottom end from.
I roll down the window and the 1st thing outta my mouth is "hey we gotta talk about dfi!"

So if the chip upgrade has boost control on it, i can start with that and then do dfi. If so then i have a good plan.

So does this chip have boost control built into it?

do i have to de-solder anything to install this 'prom"
ed

btw
E it was the biggest turbo mike had in his latest deal you cant refuse on pte turbo setups, better than group purchase price.
Maybe pte had to reduce year end inventory.. tax savings.
 

BillC

New member
ed hess said:
For boost control just use the old atr valve i have in a box someplace?
It depends. If you want to manually control boost, use that old valve. If, however, you want the ECM to control boost, you'll need to use the stock solenoid.

ed hess said:
So does this chip have boost control built into it?
If I remember correctly, BG's 50# programs do not have boost control. It really isn't too hard to dial that in, if you can burn your own chips or know someone who can do it for you.

ed hess said:
do i have to de-solder anything to install this 'prom"
No, the eprom fits into a socket. So, changing proms is nothing more than prying out the old one and pressing in the new one (facing the right way).

If you really want to keep the stock ECM, and you can't find anyone up your way to do the chips, you're welcome to drive down here (central Maryland) for us to work on the tuning.
 

ed hess

race or get outta the way
bill

I would rather not use that stinkin valve.

Wonder if they can make me the 50#head /cam chip with the boost control on it?

I grew up in silver spring. kennedy high school class of 75.
Depending on your age, you remember seeing a pearl white duster with green spider webbing down the side, and geometrics on the hood and trunk? was in a injectors of md car show in 74.

I was a member of a chrysler club back then, the name ron lynch (dart seen in dc rod & custom show) and Ian (63 impala convertible, more gauges than an airplane, tons of chrome supersport same show).
Butch nievas, custom painter?

Where exactly are you in silver spring?

Wonder if they can make me the 50#head /cam chip with the boost control on it?


ed
 

smeagol

Active member
ok, lots going on here, lots of questions.

chip - it doesn't have boost control yet, but I'm sure it will be integrated down the road. The main reason it doesn't is that we've never had much opportunity to dial in boost control for the PTE stuff yet. Once that is done, it will probably be put in the chips. The PTE has a base boost of 15psi. That is great to get going for break in & beginning tuning. You have many options for boost control - dial in a chip, wait for some chip cals with it in there, Ramchargers, bleeder valve etc.

The 50# cals for the combo you speak of are evolving everyday. We are getting more and more guys running that build, and more and more people are chipping their trucks. So the calibrations will only get better, and it is getting to the point that if you need some tweaks, you can get some help.

As far as going real fast, custom tuning while datalogging a wideband 02 is really necessary. Also, the 50s are good to 600hp at the crank. IMO, if you want 10s, go to 75s, do some custom calibrations. 50s will get you far though, especially if you plan on doing alcohol/propane etc in the future.

The old DFI - i am NOT a fan of. It can work and make power, but there are many concessions. The FAST/newer DFI are much better, and even those have sacrifices.

Swapping eproms is pretty easy, but it is something that scares people new to it. Bill has done many chips; finding someone with some experience in that area is a really good idea, so if he's even remotely close, it'd be good for you to work with him.

FWIW, you can always send the Ultimate to me or Mike, or whoever is into the chips, to reprogram the eprom for you. That'd get you the base calibration for the new buildup & injectors, and enough to get running and start tuning. You could go from there for customizing the calibration then.

FWIW, sooner or later, I am going to be building the same motor recipe - Vortecs, 412 cam, stronger stuff etc etc. I think it's a great motor combo, and is easily capable of 10s. My goal (coupla years out still) is 10s on pump gas on that buildup, probably a bigger turbo tho.
 

smeagol

Active member
ghettosled said:
http://www.arautosports.com/ultimate4.htm

FWIW, I have split up the calibrations for the L35s and Vortecs. They are different enough that we found it necessary not to group them together.

The Vortec cals run more timing typically.
 

ed hess

race or get outta the way
brian
I have read that link fom mike (before i posted this thread), just didnt know the current build status of that chip version.

Since the base boost on this turbo is 15 (says it right thers in the directions, once you adust the screw) ......this means i can run it just as it came without any boost control, and then it will boost but just not over 15psi.

then i get the $35 upgraade and i am good to go for startup and breakin.

correct?

ed
 

BillC

New member
ed hess said:
I would rather not use that stinkin valve.
That's probably a good idea, they seem to be more trouble than they're worth (IMO).

ed hess said:
Wonder if they can make me the 50#head /cam chip with the boost control on it?
If you find the right person, they can make you any chip you want. BG can do it, I can do it (although, not quite as quickly as Brian could) -- heck, even Myclone could probably do it. :p :) It's not that hard to do, just tedious.

ed hess said:
I grew up in silver spring. kennedy high school class of 75.
Looks like we did a geographic swap -- I grew up in NJ, and moved to MD about 12 years ago.

ed hess said:
Where exactly are you in silver spring?
Near where Kemp Mill Rd meets Randolph Rd.
 

smeagol

Active member
Boost control could be handled in a simple manner for the PTE setup IMO.

i was just going through this with Erue the other night. I had to make sure i used small words with him though 8)

Here's what I'd do:

0x03BA KWGRPMEN Threshold for Closed Loop Turbo Boost 0 RPM

setting this value to 6375 rpm will make the boost control open loop, so the wastegate duty cycle is a set value, based on the F71 table. From the factory it is a function of TPS. With the code hacks we have out there, you can make it a function of MPH. This works out pretty well IMO, to take into account the extra load from 3rd gear / TC lock, and you can scale the duty cycle down at the end of the track/high mph. This is something you have to tune a bit, but doing it this way really simplifies things.

0x2539 F71_SCALE F71 Table Scaling (MPH or TPS) 0-256 MPH
change this value at the end of promgrammer so you scale versus mph (see what works best, low mph, or the high range)

then your F71 looks like this:
0x03E7 F71 Initial Value Of WG Duty Cycle vs Throt.Pos. or MPH
% or MPH| 0 MPH 32 MP 64 MP 96 MP 128 M 160 M 192 M 224 M 256 M
---------------------------------------------------------------

(%)| 66.0 66.0 66.0 66.0 66.0 66.0 66.0 66.0 66.0


now, have your base boost dialed into 15psi with the solenoid unplugged.

when you are dialed in nice and safe with that boost level and you have some high octane for more boost, plug the solenoid in, and start dialing in the wastegate duty cycle versus boost level. 100% dc = high boots, 0% dc = base boost. So let's say you want to run 17psi. You should start your F71 table out with 10% DC maybe (across the board), or if you have an ultimate, make several bins with more and more duty cycle. Once you get one that runs near your target 17psi, datalog it in detail. Is the boost steady? does it creep at 3rd gear? if it starts creeping, you could use that f71 table to dial the duty cycle down at the mph levels it starts to rise, to counteract that effect.

there are more complicated ways of doing the control, but i'm becoming more a fan of the open loop setup.

enough, i'm tired...
 

smeagol

Active member
ed hess said:
brian
I have read that link fom mike (before i posted this thread), just didnt know the current build status of that chip version.

Since the base boost on this turbo is 15 (says it right thers in the directions, once you adust the screw) ......this means i can run it just as it came without any boost control, and then it will boost but just not over 15psi.

then i get the $35 upgraade and i am good to go for startup and breakin.

correct?

ed

Sorry, forgot to answer this in my post.

Yes, run it pure mechanical control. What i'd do is just run it through the stock solenoid, just unplug the solenoid. No ecm interference/control. When you want to start messing with ecm control/chipping, plug it in and play.

So let's say you run base boost of 15psi, then you dial a chip in for 18psi or a variety of levels. You could have a chip with 0% duty cycle for base boost level, or just put a switch in the wire to the boost control solenoid, in effect unplugging it.

Upgrade is all ya need then, $35 or catch someone close by, or in a good mood that can burn chips, or just send me some $.
 
Top