Code 59 or FAST management? ---

alwayscode390

pppssssshhhhhtttttttttttt
Hey Guys,

I have an older FAST management setup thats NEW ... and I planned on installing it with my engine rebuild ( sometime in the future ).

The main reason I chose the FAST was so I could get a good baseline tune from my engine builder/tuner ( easy for THEM to use it ... not sure if they would be able to tune with code 59 ) ... then I could tweak it easily on my own afterwords.

Should I ditch the FAST and learn code 59 ... or is the FAST a good setup to keep since I already have it?

I was thinking about this , and just wanted to ask your advice, THANKS :) ---
 

autoaddictions

Active member
Re: Code 59 or FAST management? ---

I have nothing against Code59 but you are harnessing the power of a 18 year old ecu. With the Fast system you will find it easier to use and tune with. The draw back is not using the factory harness like you can with Code 59. I use a stand alone and i wouldn't look back.
 

alwayscode390

pppssssshhhhhtttttttttttt
Re: Code 59 or FAST management? ---

PERFECT, thats what I was hoping to hear :)

I was just wondering if I paid a ton of money for something that has been replaced by a free program ;) .

Thanks for the clear-up ---
 

JSM

Active member
Re: Code 59 or FAST management? ---

Either system will require a tune, honestly tuning is very close no matter what system. I will disagree with frank in some ways especially the older FAST, actually our ECM has more features tuning capability than the older fast. (of course with 3 bar mod).

Things like TCC lockup, several drivability tables you can tune. Part of the bad name is people don't learn what all the tables do, so I will say our syty ecm having more tables can be more confusing at first glance.
 

gt67sy

Member
Re: Code 59 or FAST management? ---

I have the FAST XFI and when u start playing with these trucks u need all the tuneablity you can get. I don't think my truck ever ran as smooth and idled as good as it does with the XFI on
 

sy2675

He Saved the Pimp'n Game!
Re: Code 59 or FAST management? ---

never used a FAST, but code59 hasnt been that hard to learn the basics and its cheap in comparison.


and basic tunes are available for free.
 

WyoSyclone

Active member
Re: Code 59 or FAST management? ---

Code59 has been pretty easy for me to pick up on... it really is a robust system, and I really like the fact that the factory wiring doesn't have to be modified. On the tuning side of things... tuning is tuning - you need an understanding of the parameters and what they affect, and you need patience....
 

sy#2921

BAMF
Re: Code 59 or FAST management? ---

Honestly I learned the gm ecu's both ours and the ls stuff before the aftermarkets. Then learned the big stuff and fast and xfi. I always stick to the gm computer unless its something totally radical. Otherwise you have more than enough computer power to dial in any combo in these trucks.

You can easily convert the stock computer to P&H and run pretty damn big injectors. I got both 75#ers and 95#ers to idle and not be pig rich, stumble, nothing. Purrs like a kitten.

Its all about how much time you want to spend and how well you want to dial in the tune no matter the system. You have to decide after this "base" tune from a tuner how well you can pickup on learned it yourself to keep going with a tune. So which one do you think will suit you the best?
 

thunderace31

New member
Re: Code 59 or FAST management? ---

I Love my Fast XFI ON my Race GN way easier to work with than any other system I have used. I would us it again if I felt the need. I have done a lot of reading on the Code 59 thing and I just dont see how its better. Or easier to tune. You have to still change the chips to change the tune (total pain I think) now with the fast all you have to do is plug in the computer and flash what ever tune you want into it. I have 4 I use depending on weather condtions and street or race. If I want to race for money on the street I can drive around on one tune and then change it to go race and turn it back with like 4 key strokes :)

If did take some time to get things set up idle was the big one I run 96lb injectors and alky at 38psi of boost with an 90mm turbo. Ya its radical but it also went 8.93 last weekend with a crapy 1.99 60 foot.

Id do it again before going to a code 59 I just dont see it being that easy to change tunes with but thats just my :2cents:
 

hrodgmc

New member
Re: Code 59 or FAST management? ---

FAST xfi is an entry level into the "race" market controllers. They don't have a chance against 10K USD high-end systems. Then again, race teams go back to entry level controllers due to the complexity.

Some OEM systems are designed/mfg'd by the best aftermarket companies. GM does most in house, but that's likely to change soon.

Ford and mercruiser, for instance, use the same operating system as the NSA , but encryption level is a few steps lower.
 

WyoSyclone

Active member
Re: Code 59 or FAST management? ---

I Love my Fast XFI ON my Race GN way easier to work with than any other system I have used. I would us it again if I felt the need. I have done a lot of reading on the Code 59 thing and I just dont see how its better. Or easier to tune. You have to still change the chips to change the tune (total pain I think) now with the fast all you have to do is plug in the computer and flash what ever tune you want into it. I have 4 I use depending on weather condtions and street or race. If I want to race for money on the street I can drive around on one tune and then change it to go race and turn it back with like 4 key strokes :)

If did take some time to get things set up idle was the big one I run 96lb injectors and alky at 38psi of boost with an 90mm turbo. Ya its radical but it also went 8.93 last weekend with a crapy 1.99 60 foot.

Id do it again before going to a code 59 I just dont see it being that easy to change tunes with but thats just my :2cents:


That sounds pretty cool..... with Code59 you can use a couple of Moates parts and have the ability to switch between 8 or 16 BINs (can't remember the exact number with our ECM) while the truck is running.... the EX remote has an LED indicator which tells you which BIN you're using.

I'm pretty sure that the AFR and spark tables withing Code59 have about the same resolution as the FAST system. I still like not having to modify the factory wiring in using Code59..... if I was doing a full-on street rod, or pro-street of course I'd use the FAST.... it's just that with our trucks it really seems like '59 is the path of least resistance, and there is a good support system for it developing.
 

1madgumby

New member
Re: Code 59 or FAST management? ---

PTE sells the fast harness that will make it plug in play. no cutting wires at all.love the fast system..


I have nothing against Code59 but you are harnessing the power of a 18 year old ecu. With the Fast system you will find it easier to use and tune with. The draw back is not using the factory harness like you can with Code 59. I use a stand alone and i wouldn't look back.
 

skwayb

NWSTP
Re: Code 59 or FAST management? ---

Orr89RocZ is running Code59 on his Thirdgen and is running high 9's at 141 mph on Pump gas with 80lb High Z Injectors. Check out the videos he posted on Thirdgen.

http://www.thirdgen.org/techboard/organized-drag-racing-autocross/549788-my-9-second-twin.html

So the stock computer with Code59 is very capable of making serious power. And like Jeff said you will still need to learn all the tables of either system. It all comes down to the tune.
 

SloGN

9Sec Alky V6
Re: Code 59 or FAST management? ---

The greatest adavantage the FAST/BS3 has over the stock ecm/code59 is it has closed loop fuel control that you set in a A/F table. so if something goes wrong the ecm can compensate. IE: overboost, failing fuel pump,

I don't think the stock set-up can do that even with a wide band feeding into the ecm. I was told the only reason for the wideband is for the datalogging features only.


The Biggest problem when using a stock ecm and somewhat stock code. Job 1 is clean air and then job 2 is performance. so you have to know what affects what when making changes in the stock code.


Both systems can make great power and do it safely. but with a aftermarket system you can get it tunned much quicker VS the stock ecm.
 

skwayb

NWSTP
Re: Code 59 or FAST management? ---

The greatest adavantage the FAST/BS3 has over the stock ecm/code59 is it has closed loop fuel control that you set in a A/F table. so if something goes wrong the ecm can compensate. IE: overboost, failing fuel pump,

I don't think the stock set-up can do that even with a wide band feeding into the ecm. I was told the only reason for the wideband is for the datalogging features only.

Code59 has Closed Loop Wide Band Control that you set AFRs in a table. It works well. You want to run 13.0 AFR at X RPM and y MAP. BAM it will go to 13 AFR. Only caveat is it doesn't work yet when you get into PE Mode (basically anything in Boost).

The stock code goes OPEN loop (runs the VE numbers only that are in the F29x tavble) once you go into PE so it drops out of the closed loop routine where the Wideband Code that Dig and Don added is making the adjustments to the fuel in Code59. In the future we may change that and allow the Wideband to make adjustments in PE Mode. Hmm.. something I will to bring up in the Black Chat Friday (11/27 9:30pm EST) Dig is having on the SyTy Chat to see if he wants to do that and when.
 
Top