Complexity of Head installation?

Trizney

Donating Member
I had to pull my 1500 mile freshly rebuilt engine out because of bad knock on number 5, most likely from a rod bearing. I pulled the engine pretty much by my self and removed the heads as the machine shop only wanted the short block. Using tech weasels page and reading numerous posts from the search feature, I got through the removal. Now, when I get the shortblock back in 2 weeks, I will need to piece everything back together. My pops was at the shop that I rented out a stall, and he was talking to the mechanic there and he told me I was going need help installing the heads. From reading the Haynes, I just need to torque everything down in a specific order and at the proper torque rating, right?

Any info would be appreciated. Didn't find anything on search.

Side note, I am looking for some L35 heads at the cheapest price I can get. Where is the best place to get them? Anyone selling?

TIA,
Trey
 

Falco

Donating Member
It's not that difficult, but there are a couple of things to take care of. Don't forgett to use thread sealant on the head bolts before you put them back. I've followed the tightening sequence in the service manual and went with two steps. One year and no problem so far.

You could have problems to put bakc the exhaust manifold, couple of post on this topic. Take your time to clean the surfaces of the block, the heads and the intakes. Apply RTV evenly on the edges when you put back the lower intake. I'm using FelPro head gaskets and factory ones on the intake sides...

HTH,
 

jwaller

Evil Genius/SyTy Guru
I've always got L35's layin around. what do you want done to them. or are you lookin for stockers?
 

Trizney

Donating Member
jwaller said:
I've always got L35's layin around. what do you want done to them. or are you lookin for stockers?

Just looking for stockers now.

Also, I was talking with a guy today, and he said he never re-uses head bolts, as when they are torqued the first time, they stretch a little, and to use them again could be a point of failure in high HP applications. Anyone ever heard of this?

Trey
 

jwaller

Evil Genius/SyTy Guru
Trizney said:
jwaller said:
I've always got L35's layin around. what do you want done to them. or are you lookin for stockers?

Just looking for stockers now.

Also, I was talking with a guy today, and he said he never re-uses head bolts, as when they are torqued the first time, they stretch a little, and to use them again could be a point of failure in high HP applications. Anyone ever heard of this?

Trey

ya head boltsI dont use anyway I always use studs. stockers in used condition are 260. and rebuilt are around 550.
 

bezerk

New member
It's not that difficult, but there are a couple of things to take care of. Don't forgett to use thread sealant on the head bolts before you put them back. I've followed the tightening sequence in the service manual and went with two steps. One year and no problem so far.

Do all of you guys use thread sealant on the headbolts, even with ARP?
never heard something like that before (only use the bush and sleeves lock-tite, when the thread was damaged and you drill out the old thread to install a bush)
i learned that you torque the bolts. because they have the best strenght at that torque and they will not get loose with that torque.
i even have a formule to calculate the torque that it needs, so it won't loosen up.
 

Methuselah

New member
bezerk said:
Do all of you guys use thread sealant on the headbolts, even with ARP?

The cylinder head bolts pierce the water jacket in the block. Sealant is used to keep the coolant where it belongs in the block.

It's a terrible casting idea but maybe there was a good reason for it.
________
MAZDA XEDOS SPECIFICATIONS
 
Last edited:

SY2932

Administrator
Don't forget to chase the threads in the block with the appropriate tap to clean out any sealant/corrosion prior to bolting on the new heads. If you don't, it will affect your torque readings...

Also, use liberal amounts of antisieze when you bolt your exhaust manifolds back on. You WILL be happy you did if you ever have to take them off again. HTH's

Mike Campbell
 

bezerk

New member
The cylinder head bolts pierce the water jacket in the block. Sealant is used to keep the coolant where it belongs in the block.

thanks for the info, never played attention to it.
good to know, before put the heads back on.
 

Trizney

Donating Member
jwaller said:
ya head boltsI dont use anyway I always use studs. stockers in used condition are 260. and rebuilt are around 550.

the rebuilt ones come with new valves, guides, springs, seals? what parts are used to rebuild these? I am fairly interested. Do you use shims on the springs?

Trey
 
Top