Convert Ultimate 50# to $59 bin?

yudlose

New member
I finally got my first bin file to upload a couple days ago. Code 59 rocks! I'm have a few problems with some of the starter bins I've downloaded. They're all too rich! For grins I loaded the V4 Ultimate bin ''2003'' for 50#, which I believe is timing 2, fuel setting 3. This by far is the best bin my truck likes, but its code 58 based. How do I convert this file to a code 59 format or does someone already have this? I'd like to use autotune but my WBO2 just says rich for all the other starter bins when I get into any sort of boost. I have a PTE44 with 50#, a 3000 lockup vigilante, and methanol. I think the main problem is that I'm at 5300ft. With the V4 "2003" bin setting I can run 24# of boost with no KR and my WBO2 reads right around 11.0!
 

skwayb

NWSTP
Re: Convert Ultimate 50# to $59 bin?

I don't normally recommend converting bins since it is garbage in/out situation that is why we made a bunch of base bins.

But if you want, e-mail me the bin at paul@code59.org and I can convert it. let me knwo which wideband you have so I can get that set.

Also you will still need to adjust it some after it has been converted. You might have to play the F28 table to get the idle back where it was when it was 58. And you might need to adjust f29x in the boost section of the table as the fueling might be a little off due to the conversion. So be very careful geting into boost once it has been converted to make sure there are not any problems. Last thing we want is you to blow up your motor.
 

yudlose

New member
Re: Convert Ultimate 50# to $59 bin?

Thanks for the conversion! Once again, CODE $59 ROCKS :tup:
 

yudlose

New member
Re: Convert Ultimate 50# to $59 bin?

Runs great at WOT! The AFR is about 11.0 with the alky. I hope to richen it up a bit to around 10.5 and then maybe play with the timing. It's at 17* now. There are a few cruise issues but I think it'll clear up after a few autotune runs.
 

BoostedSUV

Active member
Re: Convert Ultimate 50# to $59 bin?

I really need to start messing with code 59... Hear nothing but great things but I don't know where to start and don't have a clue what I'm doing. Lol I have datamaster, tunerpro, moates adapter and flash n burn.
 

yudlose

New member
Re: Convert Ultimate 50# to $59 bin?

I have datamaster, tunerpro, moates adapter and flash n burn.

I was there too since last summer. I finally got the time and did the research with the WBO2 computer mod and the rest was fairly easy - especially with all the great help on the board. I also watch all of the tuneyfish videos - 5 or 6 in all. Check it out - tuneyfish
 

yudlose

New member
Re: Convert Ultimate 50# to $59 bin?

I'm currently having a high idle - 1800 or so. After a few autotunes I thought it would come down. I'm having similar symptoms as Aeroking at code59.org. I disconnect the Tan/black timing wire and the idle drops back down to about 1200. There doesn't seem to be any vacuum leaks and the IAC seem to be working right. Any insight as to what may be going on?
 

JSM

Active member
Re: Convert Ultimate 50# to $59 bin?

ALDL mode? What does desired idle say? What are your IAC counts during this? Does TPS reading show 0%?
 

yudlose

New member
Re: Convert Ultimate 50# to $59 bin?

I'm not sure what ALDL mode is, but the desired idle is 700. When I first start it the IAC counts are around 40 and then they end up at 0. I understand that this sounds like a vacuum leak, but I've traced all the vacuum lines and they are all connected. I've even sprayed starter fluid around the intake to see if the idle jumps with no luck. I took the throttle body off, cleaned it really good, adjusted the throttle stop and put in a new IAC motor - the old one didn't seem to zero out. The tps is at .39V. I just think that its weird that the idle drops every time that the EST wire is pulled. Other than the timing being purely mechanical, I'm not sure what else this does.
 

JSM

Active member
Re: Convert Ultimate 50# to $59 bin?

IAC = 0, desired 700 tells you the engine is getting extra air from somewhere. Vacuum leak you mentioned, but there is a set screw on the throttle also, as you could also have some linkage bind.

TPS voltage doesn't mean shit at this point.
 

yudlose

New member
Re: Convert Ultimate 50# to $59 bin?

The throttle stop I adjusted was the set screw you are talking about and I adjusted that. In fact I took the whole throttle body apart and cleaned it real good and verified that it was closing properly.
 

JSM

Active member
Re: Convert Ultimate 50# to $59 bin?

IAC counts of zero tells me its getting "extra" air from somewhere.

Hard to tell you where without being there, once you find it you will go aye.
 

yudlose

New member
Re: Convert Ultimate 50# to $59 bin?

ALDL mode?

I never did figure out what configuration of the hardware put the ecm in ALDL mode. My Ostrich 2.0 is set on "28/32" and "28" for the switch setting on the side. Is it possible to place it in ALDL mode with the setup I have? Do I have the switches set correctly?

I'm still trying to find out why my idle is high. I've blocked off every vacuum port and checked the EGR but still no normal idle. I'm also thinking it may be a torn intake gasket to the inside of the motor.:dunno:
 

JSM

Active member
Re: Convert Ultimate 50# to $59 bin?

Moates USB datalog cable has a switch to put it in ALDL mode. If you have that cable look at that switch, its not on the ostrich at all.

Desired of 700 rpm tells me that is NOT the issue though, but a vacuum leak somewhere. bike intertube over the Throttle body and 5-10psi might help find the problem.
 

yudlose

New member
Re: Convert Ultimate 50# to $59 bin?

Thanks for the "pressurization test" help. There was a huge leak on the intake upper and lower plenum gasket right by the distributor (#6 intake port). It looks as though its been apart before and the gasket was missing so someone put silicone for the missing gasket - about 1.5" along the intake:2gun:

I guess a "few" 26# runs blew it right out.
 
Last edited:
Top