Custom air to air?

syclone2365

New member
just wondering what the benefits would be of a custom air to air set up such as fitting an A2A behind the gril...not sure if its possible or if it would help out at all with the mods i have now: je pistons 30 over, ult. chip, 17psi, stock turbo, afpr, walbro 340, hot wired IC, SS IC pipe w/ RFL. please dont flame me too bad for this post if it's an outrageous question but i just thought i'd ask thanks
 

spooldup

Super Member
A2A seems like the better choice to me. It seems that the exhaust manifolds kinda dampen the effect that our stock ic's have. Dumb design. Once the w2a unit's heat soak it takes some time to cool off again as well as the intake has to cool back down. Here's a shot of my dual setup in the thread i threw up in memeber's projects. I think one of the canadians(white/gray ty?) has a massive unit in front. You might have to cut the grill and stuff to get his unit to fit. The one i have only needed minor shaving of the grill. A2a is laggier than the stock unit but i feel is a better ic than the stock or even upgraded w2a units. My temps were instantly 15-20 degrees cooler with this setup. Here's the pics, http://www.syty.net/phpBB2/viewtopic.php?t=32017
 

ghettosled

SYTY SUPERSTORE
If you get an efficient and properly sized core the gains would be pretty substantial, however horsepower wise you need to get a bigger turbo to see a major et reduction.

The general consensus is that most of the good cores which fit behind the grill require removal of the AC, Some Cutting, and/or increased radiator temps. Keep in mind that size isnt everything. YOu need to look at efficiency, flow, pressure drop, surface area, etc.

I would have to say that either the RPM IC setup or the McCoy setup should be the design of choice up to around 600hp. After this point you need to start compromising.
 

4C FED

Absolutum Dominium
I've got one that I picked up off a list member (BigAl).
It uses a Griffin 2.5" core and has HKS end tanks on it.
It is as large as can be practically fitted behind the grill (10"x20").
 

badnewz

Member
Has anyone other then lingenfelter placed the radiator in the pick up bed to make room for a big front mount air to air? I am seriously thinking on doing this, on my sy, to make room for a pte grand nat. fmic, that I have. I have it all worked out in my head. :drinking:

Mike B

St.Clair Shores,MI
 

badnewz

Member
Has anyone other then lingenfelter placed the radiator in the pick up bed to make room for a big front mount air to air? I am seriously thinking on doing this, on my sy, to make room for a pte grand nat. fmic, that I have. I have it all worked out in my head. :drinking:

Mike B

St.Clair Shores,MI
 

Sy769

Donating Member
It is on my list of things to try when I blow the sy engine.
Would be nice to have all that room for a serious A2A
 

93ty475

Donating Member
badnewz said:
Has anyone other then lingenfelter placed the radiator in the pick up bed to make room for a big front mount air to air? I am seriously thinking on doing this, on my sy, to make room for a pte grand nat. fmic, that I have. I have it all worked out in my head. :drinking:

Mike B

St.Clair Shores,MI

my sy had an auxilary radiator in the bed when i bought it...i couldnt believe it... :eek: ...first thing that i removed...
 

nick041881

Member
i did a custom front mount on my truck and it works great. i ordered a core off of the dsm website listed in the links section. i cut the hood latch core support thing out and it fills the entire front grill space. i could have spent a little more time designing the piping, but i still think the way its routed is 100% better than the dequick a2a. my intake temps are great and it cost me less to make than it would be to buy a pre fabbed one. the core is not huge but its good size and still fits my huge sheetmetal radiator, so i dont think putting the radiator in the bed is the way to go.

nick
 
Top