Datamaster analysis, please!

qbnkiller

Conflaguration Specialist
I have #1600Ty in Michign, and I have gone through and changed cap,rotor, plugs (NGK UR6), wires. I went to my local track (Thunderbird Raceway in Muskegon) and did a few runs with my Datamaster setup. I believe I have a decent running truck, but would like for someone more well-versed with the DM to analyse a few of my runs. UI can email or post here if needed.

Rds.

MAI TY
QBNKiller
 

InvisiBill

Active member
Long time no see! I'm living in GR now, just a few blocks from Yen Ching. =)

Email me the files and I'll throw them online for others to look at...
 

spooldup

Super Member
Your injectors are being pushed hard. What are the mods done to your truck? Rule of thumb, over 80%dc is pushing it. I know stockers run up to and over 100 but why push it? Also your ic pump doesn't look to be working. Those mat temps are really high. Check the fuse?
 

Buster

New member
Re: Datamaster analysis, please!

qbnkiller said:
I have #1600Ty in Michign, and I have gone through and changed cap,rotor, plugs (NGK UR6), wires. I went to my local track (Thunderbird Raceway in Muskegon) and did a few runs with my Datamaster setup. I believe I have a decent running truck, but would like for someone more well-versed with the DM to analyse a few of my runs. UI can email or post here if needed.

Rds.

MAI TY
QBNKiller

Your trucks running pretty damn good. You might consider a 160 thermostat, working on the intercooler, which isn't too bad, but could be improved. You could also add a little timing if your looking for a better timeslip.
 

Buster

New member
92 black typhoon said:
Your injectors are being pushed hard. What are the mods done to your truck? Rule of thumb, over 80%dc is pushing it. I know stockers run up to and over 100 but why push it? Also your ic pump doesn't look to be working. Those mat temps are really high. Check the fuse?

That rule of thumb is for people that like spending money, why fix a truck thats running good? If your planning a new build and are spending money anyways the 80% things cool.
 

qbnkiller

Conflaguration Specialist
Datamaster, please!

Datamaster, please!

Here is what I have done so far to the truck:

custom aux intercooler...
TCC lockup switch

That's it! I have tried a Pitbull chip and reset the ECU, and it was worse! I went to the track today and tried a few things, including ice-down the IC and turbo housing. I have now a pretty damn good slip that shows the following:

Reaction: 0.567
60': 1.833
mid MPH (1/8th mile?) 81.67
mid time: 8.370
mpH: 96.15
1320: 13.308

IA Temp @ beginning: 122F
IA Temp @ end: 166F

Looking at this, I think that I am launching REAL HARD, but falling flat on my face above 4100RPM. At the half-way point, I am hauling ass and well into 3rd, but by the end of the qtr, it hasnt shifted into OD, and is pulling near 5K, and feels like I am trying to push a wall over. So if this is the case, where can I pick up top speed?

This winter, I am going to move to L35 heads with a cam n 'stuff, but I am still doing my 'Independant Council Investigation' as to what the hell I am going to do.

As always, recommendations are always welcome.

Rds.
MAI TY
qbnkiller
 

ZMann

vertically challenged
As far as pushing it into high rpm's... i believe most of us leave it in D...not OD.

Just checkin

Later
Zach Mann
Sy1012
 
Top