Datamaster cable came........first run help?

PPI Typhoon

DIY Madman
Ok, I have a first run around the block with Datamaster. Is there anyone that can take a look at it for me? Also, does anyone have a file of a stock truck running in "ideal" condition to compare to?

I'll email the file to whoever would like to help

TIA,

_________________
Dan
'92 Ty #1542
White/White



<font size=-1>[ This Message was edited by: PrecisionPowerTech on 2001-12-30 16:45 ]</font>
 

Wes

Donating Member
Did you have it floored? The throttle position doesn't go to 100%

There's a bit too much spark retard (actually any at all is too much). Also the oxygen sensor voltage is a little low, you want to be around 950, which would probably help with the spark retard. Do you have an adjustable fuel pressure regulator?
 

PPI Typhoon

DIY Madman
Actually, I just did another run and it wasn't floored I guess. I moved my floormat out of the way and got a good run this time with 100% throttle. I also have full 15lbs of boost.

I just uploaded it:

http://members.home.net/rhanisch1/dan3.uni

About the spark retard................I shouldn't have any? How is that accomplished? Just a timing issue?

Thanks again,


_________________
Dan
'92 Ty #1542
White/White

<font size=-1>[ This Message was edited by: PrecisionPowerTech on 2002-01-02 22:24 ]</font>
 

Wes

Donating Member
3-5 degrees of retard would be acceptable (IMO), especially considering the 91 octane gas we're stuck with. There's a lot of factors that contribute to knock. For one you want to get your coolant temps down below 200, have you put in a 160 thermostat yet? Also I would consider an adjustable fuel pressure regulator, it looks like you need a couple more pounds of fuel pressure. Also intake air temp is a factor, but it's pretty low in the one you just sent me. And yes timing needs to be accurate, and the timing mark on the balancer HAS to be checked.

_________________
Wes
93 Typhoon

<font size=-1>[ This Message was edited by: Wes on 2002-01-02 22:52 ]</font>
 

G.D. Bryson

New member
Wes. reference the low 13 run you posted. I have a dumb computer guy question: Windows asks to associate the .uni file with something to open. Give me a reccommendation?
Happiness and success to all in 2002!

Gary & Ty 1845
 

Wes

Donating Member
Ok I assume you have Datamaster on your computer? There's two ways to do it. You can right click on the file and select save as then you'll want to put it into c: -> program files -> tts -> datamaster -> testdata. Then when you run Datamaster you can go to playback file and it will be there.

Or the other way, when it pops up the box saying open with click other and then go to c: -> program files -> tts -> datamaster and select DM32xTT.exe

On 2002-01-02 23:39, G.D. Bryson wrote:
Wes. reference the low 13 run you posted. I have a dumb computer guy question: Windows asks to associate the .uni file with something to open. Give me a reccommendation?
Happiness and success to all in 2002!

Gary & Ty 1845
 

PPI Typhoon

DIY Madman
Also, aren't my intake temps high? I'm going to hard wire the pump off that relay and also run some Xylene here in the future and do a run off that. See what kind of results for the knock.

Later,
 

Tooky

Serious about performance
Dan, do you have a Walbro 255 fuel pump? Maybe it's a hunch, but your file looks like your truck is exhibiting classic Datamaster characteristics of a BONE stock truck with stock fuel pump and stock thermostat.. If you ensure your spark plugs are NGK UR5 or UR5 or ACDelco-CR42TS, distributor cap and rotor are Conrad, coil is black ACDelco stocker, and your plug wires are good recommended ones, and that your timing is in check, and that your fuel pressure is up to par, I personally guarantee that you will see noticable improvement. I mean I graphed it and right now you are making like 220 HP and 340 TQ where on my stock truck I can make 360 HP and 495 TQ at my best using the same calculations!! So you have some real power to be gained for next to nothing if you can just ensure your tune is mint. Need help , let us know.
 

PPI Typhoon

DIY Madman
Yes, the truck is stock.

I changed to the CR42TS plugs, but not a Conrad cap and rotor. I don't know where to get the Conrad cap and rotor, but I did change that out with a brass cap and rotor, which brand, I forget. The plug wires were new with the truck, but I'll go buy a new set this weekend. I'll order the fuel pump too. I guess I should do that "formula" everyone is talking about with the plugs, cap, rotor, pump, IC rewire, IC hose, thermostat, etc.

I'll do those and get back to you guys with my results.
 

PPI Typhoon

DIY Madman
I just ordered the pump.

Anyone know if I can order the cap and rotor online?? I've called around and can't find any local.

Maybe I'm just a moron..... :smile:
 
B

Blake

Guest
Just go to Autozone(if you have one nearby)and ask for the Conrad cap and rotor(its a kit). $15 or something like that.
 

PPI Typhoon

DIY Madman
I haven't even had the time to put it in. I am in Oregon right now and will be probably putting it in this next weekend. After all of the posts that I read about the troubles with changing the fuel pump, I'm a bit intimidated. :smile:
 
Top