Datamaster Data Error

Maxtor

New member
Guess it could be. I removed every ground I could find inside and outside the cab - cleaned and checked to ensure they were tight. I installed a new AC Delco alternator. I also removed the wires from the ALDL connector on the truck and soldered on female connectors to get a nice snug fit with the datamaster cable. None of these things resulted in any difference. WOT runs show voltage always over 13V and very steady. Diacom works great. The truck is well tuned.

GM Turbo - Do you have something more specific that you tried that worked?
 

GM TURBO

Sell Out
It sounds as though you have covered it.

The biggest one I have seen is the low voltage causing the timeout/data error.

Have you tried the ECM out of the other Syclone?
 

Sy769

Donating Member
Ditto for me Even added several extra grounds and the new alternator.

Also I put another new set of plug wires on -No change

My voltage on the cig lighter is about13.5 and on datamaster drops to 12.5

The one thing I did do last nite that worked was cut the exhaust off behind the converter and put on a turndown tip. :D Sounds cool noisy but I can hear that itty bitty turbine wheel a spoolin :lol: and boost comes up to 15 or so now in first gear.

Now if I can just get this damn DM to work well.

IF Anyone wants a file from last nite I can send it to ya. more good data than bad and a couple 100mph runs Maybe you guys can see somethin I am missing.
 

myclone

Donating Member
I see you have an early production sy (like mine). Seems I read on here or on TTSs' site that there were some issues with the early sy prom. If memory serves me correct the fix was to get the most recent prom avail. Dont quote me on that though as I may well be wrong.

Sounds like youve attacked the prob pretty good so far IMO. I think Id try another ECM if you have one available to borrow/buy/steal/whatever.

One last thought on grounds for now.. I worked on a fellow board members sy a while back and found the main ground to the pass side head disconnected (a eng swap was done on his truck) which fragged the ECM. Did you check that ground also. I figure you have checked it but thought Id mention it to be sure.

HTH
 

Sy769

Donating Member
Swapped out the computer today used the one off the Ty

AYBN prom installed

No change more errors.

What I need to understand is what is the source of the noise? prolly my cheap ass autozone alternator.
Tried new taylor and Bosch wires-no change I thought it would be ignition related as the MSD really amplified the problem.

bought a capacitor today 1000 mfd Gonna try that tommorow

This is really starting to get old. Emailed andrew and haven't heard back from him.
 

Typhoon #1133

New member
i am not to sure it is our alternator. i replaced mine with a 140 amp alternator and if anything it got worse. not better
 

Typhoon #1133

New member
i been looking at some DM files to see if that can help find the problem. seems like mine locks up around 60 mph or just above. what happends at 60? does something change?
 

Sy769

Donating Member
Some of the Texas SyTyer's got together for a car show. I had a chance to make some datamaster runs on two of them. Both were 92 Ty's one was completely stock the other had one of the older 10 in 1 ultimates.

BOTH linked perfectly with no adjustments to anything! BOTH had no data errors at all. High speed Low speed we all speed you get the picture. :wink:
This is with the same laptop,cable,inverter,etc. that I use on my truck. So I have eliminated that from the equation.

Yesterday I changed the coil, and cleaned those connections and the aldl connections with that spray terminal cleaner stuff. No change.

Next stop distributorville. :banghead:
 
Top