Datamaster File

Hu Ryde

Donating Member
I'm getting the pcv's today. I'll try the aldl pin trick and see if the both turn on. I checked the fuse last night it was good.

So your saying the versioned chips are not the same as a 10-1? Ghettosled confused me, o'well. Later!
 

Hu Ryde

Donating Member
I just put the pcv's in and decided to give the distributer bolt another try. No luck! It is the bolt in front of the distributer right? Well any way I had the timing light hooked up and I un-plugged the tan wire and checked the timing. Here's what I got:
1.jpg
 

crsurf1

New member
I managed to get my dist bolt loose by removing the EGR and using a quarter inch ratchet,long extension, and a swivel with 15mm socket I think. Either way it's a bitch to get to.Good luck.
Craig
SY#1542
 

Hu Ryde

Donating Member
Does anyone think my ss tube and HKS SSQV blow off valve is the problem. I don't think so, I am capable of holding all my boost. I have checked for vacuum leaks with a vacuum gauge so I don't have vacuum leaks or any thing similar. I don't see how the HKS would affect anything. I think that if anything the ss pipe would help stabilize my boost because a rubber tube would flex under pressure and steel would not. It might mess up the air flow because of a hole leading to the bov but it's on the side and if that messes up the airflow then how can we run with the intercooler? It has fins inside to chill the air? The bov is activated when the manifold senses a large drop in pressure. This is when it opens the valve. Only when there is vacuum in the manfold this occurs. For example, when I let off the gass fast it creates vacuum in the manifold because the tb blade closes and thus opening the bov to relieve the pressure the turbo is putting out still. So in my opinion the bov is out of the question for a possible problem. If it leaks, then it could be a problem. But not in my case!
 

Daron

Active member
You need to define what your problem is, then eliminate possible causes. The only prob I saw with file number 3 is you get a spike of boost and knock at the onset of 3rd gear. The other knock levels were low enough to expect ignition or fuel issues to resolve IMHO.

So, what is your truck's problem? From the file I looked at, the BOV isnt likely the cause of the spike and knock, but there is something to be said to getting your truck to as close to stock as possible when troubleshooting.
 

Hu Ryde

Donating Member
I'm in the process of disconnecting the MSD and ultimate. Or do you think I should do them one at a time? I'm also going to replace fuel filter.
 

Falco

Donating Member
Jess,

Don't modify more than one thing once. Replace the fuel filter and test it and so on. ATS=Analytic Trouble Shooting :wink:
 

G.D. Bryson

New member
Hu Ryde. Part # for PCV Valves is AC Delco 8995909; The "E" is on the flapper on bottom of valve. Ya need two. Happiness and success in 2002.

Gary & Ty 1845
 

Hu Ryde

Donating Member
Just tried turing fp up to about 58psi with vac line off and pluged. No luck, 02 mv were still low arround 850-870. Could my fuel pump be going bad? I looking into getting a gauge that I can read in-dash any suggestions? Where should I connect it to the rail? How much fuel psi should it raise with each psi of boost?
 

kwick6

Donating Member
Get some injector cleaner and run it through.
If that doesn't fix it then, oh well at least you have clean injectors.
Redline is the stuff to use, unless you can do the "thru the rail, pressurized stuff"
What does your 02 readings look like on the scan tool? Are they jumping all around fast, or cycling really slow.
If you get a fp gauge, go with the kit to mount the sender somewhere other than the rail. Your fp should go up 1psi / lb of boost.
Scott
 

Hu Ryde

Donating Member
My o2's are cycling slow but are low. There are a couple of jumps but nothing big. Where can I get redline from? What Brand of gauge? Auto Meter? Why should it be mounted somewhere other than the rail?
 

kwick6

Donating Member
On 2002-01-09 11:51, Hu Ryde wrote:
My o2's are cycling slow but are low. There are a couple of jumps but nothing big.
Time for a new one. Anyone disagree?
Where can I get redline from?
http://store.summitracing.com/partdetail.asp?part=8335
What Brand of gauge? Auto Meter?
This is the one I have.
http://store.summitracing.com/partdetail.asp?part=13501
Why should it be mounted somewhere other than the rail?
It can crack the fuel rail from bouncing around. This is what you need...
http://www.arautosports.com/fpreloc.jpg

Scott
 

Hu Ryde

Donating Member
Scott,
Thanks for all the info, I'm going to try all the other stuff first before I buy another o2, I dont think it's that old, it's a Bosch, could that matter? I also have a ATR regulator, the one with the vac line running out the side (the old one) Maby if I went with the kb acufab it might help. Anyway thanks again!
 

Hu Ryde

Donating Member
I got the timing adjusted to 0* and finished replacing and zip-tying all vac line on my truck tonight. I would like to go and do datamaster runs but am out of trial runs on it.
 

JoeLutz

New member
I'm about out of trial runs also.
Hu Ryde
can you email me your datamaster files? The link to download is no longer working. Thanks
 
Top