DevilsOwn Water Alcohol Injection Controller

denny

Active member
Anyone using this ??
http://www.alcohol-injection.com/progressive-controller-p-14.html

The controller is $125, all you would need is a pump and a nozzle.


----------------------------------------------------------------------------------------------------------------------------
Description
DevilsOwn Water Alcohol Injection Controller General Operation:
On power up the unit will blink the yellow led indicating what BAR setting the unit is setup for.
2 blinks is 2 BAR
3 blinks is 3 BAR

Then the unit will read the dial settings and calculate the slope of the progressive control.

Map voltage is read and converted to a boost value
Pump duty cycle is calculated based on dial settings and slope

When boost PSI reaches the START setting the pump will come on with a 15% duty cycle
It will ramp up to 100% as boost approaches FULL setting.
The pump voltage percentage will increase with a 0.2 pound increase in boost.
This means the voltage will step up 5 times over an increase of 1 PSI making a very linear response curve

For ease of adjustment, each dial has 21 settings that are incremental
There is a setting for every hash mark and another setting in-between each
Having the arrow close to a setting will provide the exact setting.

For example the 12 o'clock position on the START dial of a 2 BAR unit is a PSI setting of 7
It will also be a 7 if the arrow is 6 degrees to right (or left) of 12 o'clock
once it is beyond half way to the middle the setting will be 7.5PSI
This allows the user to easily set the unit to exact values without having to be fussy with the dial

For reference the Dial settings for each version are as follows:
If the FULL setting is set to a lower PSI than the START setting, the start setting will be ignored and the pump will switch on to 100% when PSI is above FULL setting and will switch off when it is below the FULL setting.


In order to prevent loading down the MAP sensor signal, the voltage input to the controller is left floating. This means that tapping into the stock MAP sensor that is connected to your cars computer will not effect the MAP voltage.

However, if the MAP input wire (green) is left disconnected, sampled voltage will be erratic and therefore pump output voltage will be erratic.

LEDs:

RED - power led - It will be illuminated anytime there is power applied to the pink wire and the black wire is grounded.

GREEN - This led will light up proportional to pump output voltage, it will turn on dim and brighten as the pump reaches 100%

YELLOW - This is the FULL/Diagnostic led
It will blink the BAR value that the unit is set for on startup. 2 for 2 BAR and 3 for 3 BAR.

It will come on solid in normal operation when the output voltage to pump is at 100%.
It will stay on until output drops below 95%
This prevents the light from fluttering if the boost is hovering around FULL.

It will blink a steady rate when the unit is faulted.

Fault:
The controller will go into fault mode if
- excessive current draw
- fault in the pump circuit
- controller overheat
- pump wired incorrectly

In fault mode, the controller will shut off the output to the pump and will flash the yellow (FULL/Diagnostic) led.

The controller must be powered down and the fault condition must no longer exist before the controller will resume normal operation.

Open circuit conditions are not monitored by this controller
This is because many alcohol/water injection pumps have a pressure switch to modulate max pressure. During normal operation the switch will open and close. When the switch is open, no current will flow to the pump. Therefore, it can be normal for a zero current condition when the controller is telling the pump to run.

This controller also is the only controller on the market that is capable of accepting direct wire connections by using screw down termanals.
 

attackdog

New member
Re: DevilsOwn Water Alcohol Injection Controller

I just have the one that came with the SMC Kit. It seems to work just fine.
-Deano
 

Flyin Ryan

hated cuz he drives fords
Re: DevilsOwn Water Alcohol Injection Controller

I have the kit but haven't installed it yet.. have too many other things to finish up first but a few other board members have there kit and were happy with it plus if you go over to the srtforums there a major vendor over there and tons of low 11 second and higher neons running plenty of boost on em without a problem. I honestly don't see a difference in ability between this kit and the razor's I had a while back.. except razor's came with nice braided lines
 
Top