Diacom hook-up Question

Anyone using Diacom, will the software work if I hook up a cable from the ALDL to my printer serial port instead of the 9 pin connector?? I have a cable from my scantool that I wanted to try. Thanks Fern Sy#477
 

TyMeUp

New member
I don't think this will work. I believe that both Diacom and Datamaster use a 'custom' ALDL cable with built-in electronics to convert the serial data into a format compatible with a PC serial port.

If you have the OTC 'VT-100' cable, I can tell you how to record, download, and print EZ-Event files from your OTC Monitor 4000E. The VT-100 cable connects to the round port on the end of your scan tool and to the serial port on your computer. If you don't have this cable, check with the store that sold your shop the scan tool (part number should be in your user's guide). I can't give you a cost on this, but I'm thinking about $30 US.

What version of Windows are you running? Makes a difference for the software.
 
Sounds good, I have to find out what model it is. But its basically has a plug into the OTC, and the other end has a cig lighter power supply and one of the round connectors that clips into the GM OBD1 ALDL. There is also another round female plug on the scantool so I assume this is were I hook up this cable to my computer, right?? I dont believe I have this one with the kit. Another thing I noticed is that when recording with the scanner its done recording at about 60mile on my speedo. It wont even last the full 1/4mile run unless iM DOING SOMETHING WRONG?? I did some searching on the net and found schematics to buils the 9pin serial cable for datamaster. Datamaster looks really good but I dont have the funds right now for a labtop. Thanks for any info you can give me on the OTC. Fern Sy#477
 

TyMeUp

New member
truckins10 said:
There is also another round female plug on the scantool so I assume this is were I hook up this cable to my computer, right??
OTC part# No. 212535 - BD-9 Female - Scan tool to PC ... or ...
OTC part# No. 212536 - BD-25 Female - Scan tool to PC

truckins10 said:
Another thing I noticed is that when recording with the scanner its done recording at about 60mile on my speedo. It wont even last the full 1/4mile run unless iM DOING SOMETHING WRONG??
The record function will record 19 frames before the button push and 19 frames after. So, count to three or four after starting your run, then press the 'R'.

truckins10 said:
I did some searching on the net and found schematics to buils the 9pin serial cable for datamaster. Datamaster looks really good but I dont have the funds right now for a labtop. Thanks for any info you can give me on the OTC. Fern Sy#477
Can you post the URL to that?

When you do get around to getting a laptop, you can setup the built-in Windows 'terminal' program to display and save a live data transfer. The OTC Scan tool also prints all its data in a text format with labels.

^^^1993-TYPHOON-AT-WOT
GM-1993-4.3L-TYPH/SYCL-VIN-Z
EVENT-2---TAG------FRAME-+10
TROUBLE-CODES:-NO-------------
HIGH-BATTERY...NO------
---BASIC-INFORMATION-BLOCK
COOLANT-TEMP----------199-F
INJ-PULSE-WIDTH-------14.3-MS
MAP-------------------50-IHG
O2-CROSS-COUNTS-------000
O2-VOLTS--------------0.980-V
RPM-------------------3550
START-UP-COOLANT------141-F
THROT-POS-SENSOR------4.44-V
---ENGINE-INFORMATION-BLOCK-
AIR-FLOW--------------168-G/S
BARO-PRESSURE-VOLTS---4.70-V
BARO-PRESSURE---------28-IHG
BATTERY-VOLTS---------12.8-V
BLM-ENABLE-NO-
BLOCK-LEARN-MULT------125
BOOST-PRESSURE-DESIRE-011-IHG
BOOST-PRESSURE--------011-IHG
CLEAR-FLOOD-----------OFF
EGR-D/C(%)------------000-%
EGR-DESIRED-PERCENT---000-%
IDLE-AIR-CONTROL------037
IDLE-AIR-CONTROL-DES--037
IDLE-RPM-X-10---------062
INTEGRATOR------------128
INTERCOOLER-PUMP------ON
KNOCK-RETARD----------10-DEG
KNOCK-SIGNAL----------YES
LOOP-STATUS-----------CLOS
MANIFOLD-AIR-TEMP-----132-F
MAP-VOLTS-------------4.39-V
O2-FUEL-STATE---------RICH
SPARK-ADVANCE-PROGRM--14-DEG
THROTTLE-ANGLE-%------000-%
TIME-FROM-START-------11.9
MINWASTEGATE-D/C------081-%
---TRANSMISSION-INFO.-BLOCK-
PARK/NEUTRAL----------OFF
TORQUE-CONV-CLUTCH----OFF
VEHICLE-SPEED-SENS----042-MPH-
---MISC.-VEHICLE-DATA-INFO.-
A/C-CLUTCH------------OFF
A/C-REQUEST-----------NO
AIR/FUEL-RATIO--------11.9
FAN-REQUEST-----------OFF
POWER-STEERING-PRESS--NORM
PROM-ID---------------0831
VACUUM----------------OFF
-------PRINTING-COMPLETE------

Now everyone can see my lastest problem.
 
Ive seen the live data tranfer area but didnt know what it was. When I went to it it said something about a modem hook-up?? Is that what you were talking about in the previous post?? Now that printed report you have just shoes the one frame??? Can you record any longer on the live transfer as oposed to just recording normally?? Its a fellow list member website, nice site, www.syty.huryde.com. Just click on datamaster and he gives you the schematic at the bottom of the page. Parts cost me $30Cdn and Im 3/4 done in one night. Never did any type of building like this before but it easy. Fern Sy#477 Dont u fuckin hate how boost is in KPa????
 

TyMeUp

New member
I had to change that fist list, sure was hard to read when these pages take out all the spaces.

The modem tranfer is for using OTC's 'Communicator' stand-alone modem to send data over the phone to Hot-Line services. For the PC live tranfer, you select the 'Terminal' mode, then setup Windows Hyper-Terminal to recieve and record. The time limit is the size of your hard drive. I did this with a borrowed laptop many years ago, so it would take some 'play' time to refresh my memory. Since then I purchased a Windows based E-Z Event Total Program ($50 US), but I still don't own a laptop.

http://www.virtualsoftware.com/ProdPage.cfm/769

I'm still using the old DOS based EZ Event software on the shop computer... downloading from the Monitor 4000E EZ-Event recordings; it does the job.

Fern Sy#477, check your PMs for my info on this software.
 
Top