DM datalog help

Turbo6

10.20@131.8
I am going to the track tonight and datalogged a wot roll on with a little race gas mixed in. Can I get an opinion of the log from someone. It looks a little lean. I have the ultilmate v3 50# on T1 22 . My site wont let me post up the file so I will need to e-mail.

Phillip
 

smeagol

Active member
It does look lean.. the first run had very low 02's with some knock. 2nd run was on a richer setting, the 02's improved and the knock was slightly reduced.

What fuel pressure is this at? did you lower it like i said? hmmmm
 

Turbo6

10.20@131.8
45 psi base fuel pressure should I start out with T2 17? Remember I have very little race gas in it maybe 10/1 mix
 

smeagol

Active member
Odd that it looks so lean..

i'd try upping fuel pressure a bit... it looks overly lean for that setting. Wasn't knocking much, which is good though. MAT's looked good too.. you have the McCoy air-air, right ?
 

Turbo6

10.20@131.8
Yeah its a McCoy IC. I was suprised at the IA temps. I may get no knock when I dump in the mother load of C16. I hate to up the fuel pressure when its rich at idle and normal driving. T2 17 would add some fuel correct?
 

smeagol

Active member
What data is leading you to say it's rich at idle/normal driving?

T2 17 will add some more fuel - but I would have never guessed you'd need that much.

I still think you may need to up the fuel pressure.

What is the ambient temperature by you?
 

Turbo6

10.20@131.8
The o2 readings are hanging around 900mv at idle and light throttle. Maybe its the headers making it lean at WOT dunno. It is about 75deg F here.
 

smeagol

Active member
I wouldn't worry about the rich 02 readings until you'd start to puff black smoke or foul plugs.

The stock 02 is going to toggle back and forth when in closed loop, 14.7:1 is 450mv. These programs are OPEN loop, so there is no feedback.

The way the stock 02 works... 900mv could be 9:1 or 14:1. The way I have it tuned, it *should* be closer to 13-14:1 for smooth running.
 

Turbo6

10.20@131.8
I see. Thanks for your input and being quick to reply. It helps me out alot. I'll put the base FP on 48 or 50 and dump in some C16 :wink: and make a pass and see what it does and go from there. I will let ya know how it ran at the track tonight. Thanks again!
 

smeagol

Active member
Do you have a fuel pressure gauge you can watch while boosting ?

Make sure your pump can keep up, just so we aren't band aiding a problem here.
 

Turbo6

10.20@131.8
Yeah have an electronic FP gauge.....looks like the fp goes up the same as the boost. It has a 255lph walbro is what les says. I put a new fuel filter on also. I will pay really close attention to the FP next time out to make sure its holding up.

Could the headers make it run leaner? This speed density stuff is weird.
 

smeagol

Active member
yes and no

i have a similar buildup, and never saw it go that lean

(headers, air/air with same core as yours, similar sized turbo).
 

Turbo6

10.20@131.8
I have never seen 2 factory o2 sensors read the same anyhow. Need a wideband. I'm outa here goin to the track....will know how it runs in a couple of hours. Too bad its hot and humid today :cry:
 

Turbo6

10.20@131.8
The truck did not run as well as it should. Only ran 84mph in 1/8. I only got a couple of runs but going from T20 to T22 didnt make a diff in the mph. It ran an 8.17 and 8.18 with a 1.75 and 1.76 60'. It still shows a little lean but with very little knock. E-mailing the DM file to you Brian. Now to find the problem :-?
 
Top