Do these numbers seem right?

s_blazin

Donating Member
Re: Do these numbers seem right?

Well stock springs could cause that. Do you have pressed in or screw in studs?

It has isky guide plates so I'm gonna say screw In studs

just get self centering roller tips. 1.6s i went 10.50 on them.. they wont hurt the wallet.

I will look into those. 1.6 isn't to large for my small setup?

For those worked over heads and that turbo, that seems pretty low. I'm in the process of a similar engine build.
I'm going with 2.00 valves though, 60lb inj's, and alky injection. According to my figures and other members with somewhat similar builds, I'm expecting @500 crank hp.

Something is off with your build. That should be making quite a bit more power.

I agree with you something is off. With a moroso valve spring check thingy and a bar type torque wrench I could just barely lean on it, about 5 ft lbs it would crack the seat. And with 2.02 valve at 17 psi that equals about 55 lbs of press on the back of the valve not adding the oil press and a stock spring only has like what 30 lbs max return spring rate I can see why it's not making asuch power at high rpm. The valves more then likely are floating like a mother! At the time of changing the springs I'm also going to Dona test to find the lift and duration of the cam. That should tell some more.

Also going with alky once i get this figured out.

So here's another thing, a 10 psi boost launch I'm only cutting a 1.8 60ft. That seems high to me. Shouldn't this thing 60 ft in the 1.6's?? Maybe the torque converter has to small of a stall?
 

s_blazin

Donating Member
Re: Do these numbers seem right?

I also only have a single fuel pump so I very well may run out of fuel before I hit my desired hp number. We had zero knock at 17psi on pump fuel so I couldve gone higher but I figures that was decent enough for the street for now. I'll turn up the boost and retune once my alky kit is on.

I'm no whiz with the running factors on these trucks but a guy I know was saying that the turbo is to small?? But it takes forever to spool for a boost launch at 10psi
 

Throws

Active member
Re: Do these numbers seem right?

Sounds like you're at Wong's Performance? Tom's a good guy, and for sure LS-based stuff is his thing. I'd been wondering too how he'd handle a SyTy.

FWIW: Go Alky. I've got one of the Snow kits, as does 5678TA. Easy and goes like gangbusters.

-P
 

dgoodhue

BuSTeD 4.3
Re: Do these numbers seem right?

I'd you have a small lift cam, 1.6:1 RR will be fine. You can re use the stock rockers that isn't what holding you back. With the power dropping off at 4400 rpm, your dyno doesnt seem all that far off. Gt some springs in and run some more boost. Your fuel pump as long as the base pressure isnt super high should out flow your 50# injectors. If you have the right sized torque converter your Sy should scream off the line.
 

Treymen

Donating Member
Re: Do these numbers seem right?

I also only have a single fuel pump so I very well may run out of fuel before I hit my desired hp number. We had zero knock at 17psi on pump fuel so I couldve gone higher but I figures that was decent enough for the street for now. I'll turn up the boost and retune once my alky kit is on.

I'm no whiz with the running factors on these trucks but a guy I know was saying that the turbo is to small?? But it takes forever to spool for a boost launch at 10psi

If you have the Wally 255, your good
 

s_blazin

Donating Member
Re: Do these numbers seem right?

so i never updated this but i pulled a valve spring and spring tested it, it's good for the boost i'm running so i put it back in. called mccoy and talked to Jerry for nearly an hr, he gave me some checks to look for but really none of them seemed to add up to whats going on here.

he was telling me that my motor should be making way more power at 17 psi and should be pulling hard to 5500 rpm which it will not. He was saying that this thing making the proper power should runs solid 12.0's and maybe even down to 11.80's.

And my 1.8 60 ft's on a 13 psi boost launch aren't adding up either......sadly enough i think at the end of the summer its time to tear the motor down and see whats going on inside. cause something is not right.

I don't know how to load my dyno graph on here, currently it's in a PDF format in my email. I'll load it if someone could tell me how
 

WyoSyclone

Active member
Re: Do these numbers seem right?

Sorry, I've been absent for a while.... I would think it may be something in your Code59 tune affecting things. Do you have a log and a BIN you could shoot over to me?
 
Top