Dropped a nut into the block

Dropped a nut into the block

  • Pull the diff and then the pan?

    Votes: 6 31.6%
  • Pull the engine then the pan?

    Votes: 1 5.3%
  • Turn the crank and let it drop out and hope it's not jammed

    Votes: 4 21.1%
  • Leave it - it's too small to do any damage and will fall into the pan

    Votes: 6 31.6%
  • Other - what?

    Votes: 2 10.5%

  • Total voters
    19

Windedv6

Ty n 10s
Re: Dropped a nut into the block

Flushed it and heard the nut plink into the lower pan. Can't get it out.

Tried to take off the oil drain fitting from the turbo but I think that it will cause a larger nut to fall off in the pan so am going to look at pulling the engine.

The heads need going over due to the ticking noise anyway so this seems like a good time to check it all.

The oil Pump pickup is blocking it from getting to the drain. You could still try a magnet (providing it a steel nut) and slide it around the pickup.

John
 

Quickstop [UK]

Combating adversyty.
Re: Dropped a nut into the block

The oil Pump pickup is blocking it from getting to the drain. You could still try a magnet (providing it a steel nut) and slide it around the pickup.

John

Be careful the "While I'm in here" bug doesn't bite you or you will be rebuilding the whole motor while its out;)

Thanks John, I'll give that a go

Seeing as I have no new lifters to install, I feel like I should just pull the heads and check out the source of the tick.

May as well pull the motor. I may have to just pull the heads from in the truck though as I haven't got the space at the moment.

When it rains, it pours!

:D
 

leadfoot

Member
Re: Dropped a nut into the block

Leave it in the pan if you know it is there. :2cents:

What are the odds it will float? -It's certainly not going to make it through the sump screen.
 

MRKING

New Parts for Old Trucks
Re: Dropped a nut into the block

Leave it in the pan if you know it is there. :2cents:

What are the odds it will float? -It's certainly not going to make it through the sump screen.

This is deffinately a bad idea , and even with vegas odds in your favor , not worth trying even once to see .

Think of all the heavy items on the bottom of the ocean floor , they still move around with tides and undercurrents .
 

leadfoot

Member
Re: Dropped a nut into the block

This is deffinately a bad idea , and even with vegas odds in your favor , not worth trying even once to see .

Think of all the heavy items on the bottom of the ocean floor , they still move around with tides and undercurrents .

Your entitled to your opinion -as is anyone. Did not know oil went through tides and currents in the pan...:rotf:

You have the weight of the oil pushing down on the nut, and eventually the suction from the pickup tube will suck it to the screen and hold it there when the engine is running -if it is not already bonded to the bottom pan sludge.

It would be a good myth for mythbusters to solve. To see if they can get a small fastener to destroy an engine.

I am almost tempted to put some used oil in a clear plastic container, put a small nut in the oil and violently mix the oil to see if it even leaves the bottom.

This guy never had a problem:

http://www.m5board.com/vbulletin/e3...59814-debris-found-oil-pump-inlet-screen.html
 
Last edited:

It's just a six

Super Member
Re: Dropped a nut into the block

Have a powerful magnet sit on the outside of the oilpan to keep the nut in one spot. Just a thought.
 

MRKING

New Parts for Old Trucks
Re: Dropped a nut into the block

LOL , i understand .

My assumptions are based off the foamed oil return from the turbo , and the 4500 revolutions per minute that aid in swirling the oil around . Without a crank scraper or windage tray , I cant imagine what will keep it from being sucked into the cranks spinning region . I'm wrong all the time (dont tell my wife i said that) and for discussions sake wanted to explain .

Have a great weekend , i running out the door now . Good luck Mark !
 

DaveP

Active member
Re: Dropped a nut into the block

Leave it. It won't move, it won't hurt anything. You seem to create unintended work for yourself every time you touch your truck. For instance dropping a nut into the engine while doing something else. Retrieve the nut the next time you have the pan off for other reasons. Don't create MORE work by retrieving the nut. Seriously, nothing goes well for you. So just leave it be. Concentrate on fixing stuff that NEEDS to be fixed.

I once dropped a 3/8-16X1-1/2" machine bolt into the distributor hole of the 396 in my El Camino while removing the lifting chain after setting the newly built engine back in the chassis. I wasn't certain it had gotten all the way to the pan sump. I R&R the intake, and it wasn't in the valley, so I assumed it was in the sump and forgot about it. The bolt was still there 8 years and 100K miles later when it came out again for work. The bolt never damaged a thing. I did the same thing you did. Made sure it wasn't located somewhere it could cause damage, but then, unlike you, I forgot about it.

Oh. And for the 30+ years since this incident, I put a cap-plug in the hole whenever I remove the distributor. I haven't stopped dropping bolts. But I have developed disciplines to keep them out of places they don't belong. Like engine sumps.

Cheers
DaveP
 

jpalmer

New member
Re: Dropped a nut into the block

I'd listen to Dave, i think he knows his stuff. ;) anyways, you mentioned rebuilding somewhere down the line, you can get it in. I would however put a magnet on the pan, maybe even glue it on and run that pig. Sure, removing it would be awesome, if it wasn't for all that hard work for a little tiny bullshit nut. just sayin.
 

Quickstop [UK]

Combating adversyty.
Re: Dropped a nut into the block

Guess I'm gonna leave it in there!

I've turned it over by hand 4 times and it's free so let's hope the nut stays put. Will put a magnet on there as well.

Cheers guys!
 
Top