Dyno numbers

cameronsclone

New member
Well i snapped the front shaft and decided now was the best time to take it to a dyno. This was actually round 2, yesterday I was on there and blew a tire, looked like it had a nail or screw in it and the rollers ripped it out. It looks like it was running a little lean for my liking, and FP was turned up pretty well, so I guess that needs a new fuel pump. Some aftermarket one is on there, but I doubt its a high flow one like a walbro, more like a stock replacement. Feels like the truck has more in it though, It got some weird ass power numbers. This was on T3 20 psi, need to adjust wastegate, My boost is consistently 2-4 psi lower than target. My laptop died so I didnt get to run DM with it on the Dyno. Can't see it that well, but I got 306 HP@4400 rpm and 395 lbft Torque@3800 rpm. Numbers aren't too bad for a truck without a real tune. On another run I got 299 HP and 398 lbft Torque. Edit: This was on a dynojet model Dyno, are those pretty acurate?
scan-1.jpg
 

dgoodhue

BuSTeD 4.3
Re: Dyno numbers

What are your mods? What type of gas are you runing to be able to run T3 timing? From what I understand you were really running 16-18psi.
 

cameronsclone

New member
Re: Dyno numbers

dgoodhue said:
What are your mods? What type of gas are you runing to be able to run T3 timing? From what I understand you were really running 16-18psi.
Yeah basically, a few psi less than target. I ran a Xylene mix that supposed to add to 105 octane. Mods are kenne bell bad dog 20g, ultimate, lucas 36 pounders, ATR big water-air with lower aux and shurflo, tranny cooler, kenne bell cold air, afpr, flowmaster 3" afte DP with high flow cat (still have muffler on too), no EGR, 160* Tstat, ATR underdrive pulleys (more trouble than their worth), Thats basically it.
 

TxSy1430

New member
Re: Dyno numbers

where did you get it dynoed at? You going to the Round Rock carshow Saturday night? I'll probably be there around 6:30..
 

cameronsclone

New member
Re: Dyno numbers

I will have to see, seems like I'm supposed to do something on Saturday, cant remember what though.. I did it at Maxwell Dodge on 183 and 620. About 15 miles up 620 from the car show.
 

TxSy1430

New member
Re: Dyno numbers

MZM has an 4 wheel dyno. they told me they get $80 to do a few pulls on it. I think I may take mine to them and see what kind of numbers I'll get. If I had to guess I would say I have 350 at the wheels with the mods I have.
 

cameronsclone

New member
Re: Dyno numbers

TxSy1430 said:
MZM has an 4 wheel dyno. they told me they get $80 to do a few pulls on it. I think I may take mine to them and see what kind of numbers I'll get. If I had to guess I would say I have 350 at the wheels with the mods I have.
WTF?? I went up there a few weeks back and they said $225! Hmm, I guess they just ment to tune it. Oh well I didnt get too bad a deal, $65 for how ever many pulls i wanted, lol. All the guys there were kind of excited to see it go, and i did like 4 or 5 pulls. Looks like I wont be able to make it out tomorrow night though, going to a party or something. Hey give jim duda a call or pm him, he lives pretty close and I don't know if yall have met. His poor syclone hasn't been out in a while. He has that syclone and a Typhoon loaded with ATR goodies. PM me if you dont have his #.
 

syclone3

Member
Re: Dyno numbers

I hear all sorts of prices for dynos in CA. I try to be reasonable and with an AWD vehicle, just pulls with the wideband and map sensor connected. $100 for five. Once its on and running doesn't take that long to do that many runs. When someone wants to tune their own vehicle its $125 an hour unlimited runs. When I tune its $175-250 per car for a reflash, i.e. EVO or Subaru.

Might post up a mini Syclone and Typhoon meet for this fall on the Mustang dyno. See who shows up. CA guys are more than welcome. Will make it really affordbale so its worth their trip up here.
 
Top