ECM B fuse keeps blowing...???

Gmoney

New member
I was driving home today and when I jumped on to go through a light the engine shut off and wouldn't start, I checked some fuses and the ecm b was blown, threw a new one in, started it and it blew again. So after talkin to Will , we thought it might an ecm prob, he let me borrow an old one, put it in, fired up, but then when you put load on it, it blows the fuse again. Any thoughts or help would be awesome!
 

Loeryder

New member
Garin,

Whats up man?

ECM B also supplies the fuel pump.
What size fuse are you using?
You can go up 5 amps, but if your running a stock pump still this is a sign it is going out.

Tell Will he's coming over for beer and fuel pump.
He's done a few of them I am sure.

cya
 

Gmoney

New member
I have already put a walbro 255 in about two 4 months ago. It has a 10 amp fuse in there now, thats what it had in there when I got the truck. I hate electrical problems!! :D
 

Loeryder

New member
two 4 months ago
Well which one is it? two or 4???
j/k

Yeah, the 10A fuse is barely adequate for the stock pump so its not uncommon to have to go up a few amps.

Toss a 15A in that bitch and forget about it.
 

Gmoney

New member
I figured it out, i have fuel cut switch that had a wire that had worn through and was grounding out in a piece of metal, so i just rewired it all good now. Thanks for the help Jason :D
 

QUICK STORM

B.A.M.F. BMW Tech
also if anyone wants to know, if wiring is all good and the fuse keeps blowing replace the oil pressure switch, its on the same circuit as the fuel pump and if bad, oil pressure will go to max, 80psi, and it will pop the fuse after a while, and the symptoms you had will show up everytime. this happened to me.
 

InvisiBill

Active member
I suggest hotwiring your fuel pump when you change it. These trucks have enough electrical issues as it is. I think it's much better to move the main current draw of the fuel pump to a separate wire, than to put even more load on the stock wiring.

The Racetronix harness (http://www.syty.net/phpBB2/viewtopic.php?t=18057) is nice, or you can make your own if that's your thing.
 

spooldup

Super Member
i never heard of this mod? When you do a walbro you should always install a larger fuse? Mine's been working fine forvever.
 
spooldup said:
i never heard of this mod? When you do a walbro you should always install a larger fuse? Mine's been working fine forvever.

Upgrading the wiring harness is required for proper pump performance and avoiding electrical problems in a Sy/Ty.

A 20A fuse is recommended for a Walbro GSS340M pump to handle the startup inrush current demands.
 

E-Rue

New member
Racetronix said:
spooldup said:
i never heard of this mod? When you do a walbro you should always install a larger fuse? Mine's been working fine forvever.

Upgrading the wiring harness is required for proper pump performance and avoiding electrical problems in a Sy/Ty.

A 20A fuse is recommended for a Walbro GSS340M pump to handle the startup inrush current demands.

i hate racetronix
EXTREEMLY hard to deal with on a vendor level, i hope that their customer service for individuals is a LOT better.

because of this, if i come across a truck thats having voltage problems i just build my own harness. also not all trucks need a harness..... they are however extreemly useful when using a voltage increasing device such as the MSD. (increases voltage to the pump as boost pressure risses)

e
 
E-RUE said:
i hate racetronix
EXTREEMLY hard to deal with on a vendor level, i hope that their customer service for individuals is a LOT better.
e

Our customers and dealers have no issues with Racetronix.
Customers who have bought a Sy/Ty Racetronix product have received quick service and a quality product.
You are not a Racetronix dealer so you have no basis for comment.
Perhaps this is where your beef is? Regardless it is not very professional to start trashing other dealers or manufacturers in a public forum.
There will be many products in the coarse of doing business that your company may or may not have access to. This does not give you justification to discount the product's quality or performance or to trash its suppliers and / or manufacturer.
 

SY2932

Administrator
Gentlemen, if you have any grievances with regards to the business end of how a manufacturer operates please take it off this forum. Be it via PM's or emali. Bashing a vendor here is not within the scope of this topic. Thank you :).

FWIW, I have never had to upgrade to a larger fuse after I installed my Walbro 255 pump and that was over three years ago. However, I am very particular about my grounds. They always get addressed anytime I do anything electronic related. The ground for the fuel pump can get pretty nasty over time. The one on my daily driver 1988 S10 was almost corroded in two when I was messing with the fuel pump in it :eek: .
 
SY2932 said:
FWIW, I have never had to upgrade to a larger fuse after I installed my Walbro 255 pump and that was over three years ago. However, I am very particular about my grounds. They always get addressed anytime I do anything electronic related. The ground for the fuel pump can get pretty nasty over time. The one on my daily driver 1988 S10 was almost corroded in two when I was messing with the fuel pump in it :eek: .

A GSS340M will draw apx. 5-7 amps @ 13.5V @ 300KPa.
Since the Sy/Ty FP wiring is very weak the supply voltage to the pump will be lower which will reduce its current draw. The startup current is further moderated by the resistive factory wiring which will reduce the inrush current and possibly prevent the factory fuse from blowing. Either way it is a good idea to get the fuel pump power source off of the factory wiring when upgrading to a pump which draws much more than a factory unit. This is the only way the Walbro pump will be able to meet its flow specification.
 

SY2932

Administrator
Yes, if you intend to run a MUCH larger fuel pump by all means ditch the factory wiring and go to a larger wiring harness. Much in the same way that if you choose to upgrade to higher output headlights needing to go to a larger wiring harness because the stock one will melt if you don't... I was simply making the observation that going to a aftermarket fuel pump didn't necessitate me going to a bigger ECMB fuse and/or upgrading my wiring. I run 20 pounds of boost when I take my truck to the track and don't have any fuel delivery issues and countless others have as well using the stock wiring. However, what works for me may not work for others YMMV.
 
Top