engine out take a look

SloGN

9Sec Alky V6
hey guys

I recently removed the engine from the Sy.. It has been giving me this hard knock/rattle at start-up...

The previous owners must have had the engine out at some point as the rods and caps have been stamped ? ( is this factory) .

Also are these engines internally balanced or external? The flex plate has a big weight on it like its setup for external balance.. But the front harmonic balancer looks to be neutral balanced?

I'm not very familiar with the chevy V6's as i am the Buick v6's
 

Attachments

  • IMG_1347.jpg
    IMG_1347.jpg
    48.8 KB · Views: 3
  • IMG_1349.jpg
    IMG_1349.jpg
    48.4 KB · Views: 3
  • IMG_1351.jpg
    IMG_1351.jpg
    55.5 KB · Views: 3

SloGN

9Sec Alky V6
Re: engine out take a look

That is not an OEM oil pan gasket, nor is the use of red RTV on the rear cap
Rods are usually stamped. But not like that.
The bearing shells have a date code on the back side. That will tell you about when the bearings were installed / last time the engine was apart.
Flex plate on the 4.3 is weighted.
Those main bearings look like pretty much every SyTy main bearing I've seen upon tear down. The bearings don't seem to last very long, especially at enhanced power levels.


Thanks dave !!!

The bearings are clevittes.......The only number is saw that might be a date is 3. 04

so is that 3rd month of 2004?

Lucky the bearings are std..ones.. so maybe with some luck i can polish the crank and use some 1 over bearings..

Also where can i get the specs for this engine?


Thanks again !
 

SloGN

9Sec Alky V6
Re: engine out take a look

I have never liked Clevites. they have a reputation, but in my close to 50 years of engine building I've found they just don't hold up. They're too soft. I have a local peep's engine apart that had Clevites that look just like yours (shot) with not many miles on them.

For decades I used a Federal Mogul AP bearing that gave great service. The AP-series was an aluminum backed Babbitt that was fairly hard and durable. The AP is no longer available. I have been using ACL bearings that the engine shop I'm now using recommended. I just now went to get the brand off the box and saw "made in China" on the box. That's a disappointment. I didn't know that.

Yes, that is probably a March 2004 date.

I use the GM service manuals for specs and torques. I also have personal guidelines for bearing clearance I've developed over the years from experience. Ie, I've lost a couple of bottom ends (mostly big blocks) when I had a premonition the clearance wasn't what I thought it should be, but ran it anyway. If you want, I'll share what clearance I like to have in a streetable SyTy engine. Do try to use your crank as-is. Turning them makes them weaker, and if the grinder guy gets it wrong, establishing the correct clearance becomes almost impossible. The engines I lost were all with re-ground cranks that were just slightly over or under tolerance making the clearance too tight or too loose. It took me 20 years to find a crank grinder that can hold the tolerance I desire.



Yes if you dont mind sharing your clearance set-up with me. i would be very thankful...

What im hoping for is that i can polish this crank out and maybe get away with some .001 over bearings...

The third main journal looks the worse...but i dont have the rear cap off yet...

Also whats the balance spec on these engines....36.6% ?
 

SloGN

9Sec Alky V6
Re: engine out take a look

Update.....

I got the engine apart and starting digging....

The crank is gonna need a regrind and polish ...The front main journal is out of round by .003 .. The rods just needs polishing as they are...

The cylinder bores have about .006 wear at the top and .002 at the bottom...

So now the block is off to the machine shop for cleaning and boring for new forged pistons ..

I checked the rods and they appear to be straight...I check them on a marble precision ground table...

I also noticed the rods are offset like a Buick ...this must be due to the split pin crank design...

I think I'm gonna replace the rods anyhow but thought I would note if they were bent....


I think I'm gonna source a set of L35 heads to complete this somewhat performance build.....
 

Gnocide

turbo game burt reynolds
Re: engine out take a look

nice
Patrick if your engine is being done where my transmission was- you will have no problems or worries


unless lunchbox and his kid show up.........
 

Don W.

Stab it and steer it
Re: engine out take a look

I imagine you know this but...

With new rods and pistons I would definitely consider having it balanced, and by someone who knows how and has the correct bob-weights.

What rings and bearings are you gonna use? You'll need one set of rings and a rod bearing to balance it.
 

SloGN

9Sec Alky V6
Re: engine out take a look

I imagine you know this but...

With new rods and pistons I would definitely consider having it balanced, and by someone who knows how and has the correct bob-weights.

What rings and bearings are you gonna use? You'll need one set of rings and a rod bearing to balance it.

Yes sir I know that the assembly needs to be balanced.....

This is not my first engine build...just my first Chevy v6 ...

I built my stroker 3.8 engine and a few other over the yrs.


Yes John I'm building it at the turbo Buick Mecca........

It's gonna be epic......
 

Don W.

Stab it and steer it
Re: engine out take a look

X2 on the Clevites. I'm using King main bearings for one simple reason. The have a main bearing with a 3/4 groove. More oil to the rod. They also just seemed to fit better.
 

Gnocide

turbo game burt reynolds
Re: engine out take a look

Yes sir I know that the assembly needs to be balanced.....

This is not my first engine build...just my first Chevy v6 ...

I built my stroker 3.8 engine and a few other over the yrs.


Yes John I'm building it at the turbo Buick Mecca........

It's gonna be epic......

if lunchbox cant make it - ill come down work the air hose
i dont know if i can do it for 10 straight hours tho!
 

Damian

Member
Re: engine out take a look

X2 on the Clevites. I'm using King main bearings for one simple reason. The have a main bearing with a 3/4 groove. More oil to the rod. They also just seemed to fit better.

I'm using Clevite right now and I'm wanting to pull the motor and use King bearings next time. I was looking at their race bearings.
 

coupecustom

Member
Re: engine out take a look

I ended up using the SI series on my recent rebuild. The differences between the SI series and the HP series is the HP's provide better oiling for use on higher RPM motors. So depends on your build and budget for what series is best.
 
Top