eprom editing

Mick

New member
Hi,
I am newbie here, so I thought I would introduce myself.
My name is Mick (obviously), and although I do not currently own a SY/TY, I have been involved in forced induction performance for quite some time. My current project is a GM 3100 pushrod V6 roller motor retrofitted with a Mitsubishi Heavy Industry's TD05H 16g turbocharger, that has been installed in an 88 Pontiac Fiero. I am considering a SY/TY as my next project, and this site has proven to be very valuable for research and information.

There seem to be many very knowledgeable folks here that burn their own EPROM's, and so I thought I would also mention some eprom binary editing software that I have developed. The software is called GMPCM. You can view more info about it, and also download the software directly from here.
I would like to invite you to check it out if you find time, and perhaps offer your opinion of it.

Mick
 
B

Blake

Guest
Thanks for putting this out there. So far, however, I'm getting all kinds of various runtime errors(13,26,...). I'm running windows XP. From what I understand, runtime errors are sometimes caused from missing files. Any other ideas? I tried playing with a bbzb bin and gave up after the 4th runtime error. Kinda aggrivating because it closes the whole program out, you lose everything you were working on(for the last 30 minutes) and you crash to the desktop.

BillC has also written a bin editor and it converts everything to normal values and you have slide bars to adjust all the settings. Syty specific though. It's really nice.

Thanks again,
Blake
 

Mick

New member
Hi,
The only person to date that has reported problems such as those had a corrupted operating system. He reinstalled his OS a few weeks later due to other obvious problems, and noted that the software ran fine after that.
Running the software under XP also requires significant amounts of memory, 256mb is genereally the minimum I recommend.
The software was developed on an XP pro box, and there are quite a few people currently running it on XP and win 2000 machines.

Another likely source of your problems may be related to the fact that the demo definition file included with the software (ie.. $A1.pcm), is not designed for the SY/TY binary files. The SY/TY specific definition is called $58.pcm, and can be download at the GMPCM website from here.
If you do not yet have a SY/TY $58 binary file, there are also a few available for download here.

Mick
 
B

Blake

Guest
Thanks for responding so quick. No problems on the system setup. No other problems with any other programs. 256 megs of RAM, 1.7Ghz, OEM XP home edition. I did reboot the system as it requested after the install.
Just thought you wanted feedback.
Guess it just won't work on mine.
Thanks,
Blake
 

leroy

Donating Member
Works okay on mine. Nice work! I need to do some more work on the 749.ecu file.

Jim
 

Mick

New member
Yes, I do welcome feedback. If there were an actual problem with the software I would also address it immediately, as I have a significant base of current installations that could be adversely effected. It has, however, been extensively beta tested on various platforms, including a windows 98 laptop with only 24mb of ram. It is also working flawlessly on "numerous" other systems at this time. Although I am sure that there may be some machines out there that could have issues, your system sounds quite similar to the machines I do most of my work on here, so it should work just fine on it...

Mick
 

Mick

New member
leroy:
The GMPCM software can export a Winbin .ecu file directly, so your task is now almost finished. :) You do need to filter down the number of items so that Winbin can load it though. Just click on the "normal" box to uncheck less critical items and they will not be included in the exported Winbin file. Winbin is limited to just over 200 total items, and my "PCM" definitions are typically comprised of between 500 and 900 items. A PCM definition is intended to represent a complete mapping of the data portion of the binary file, an entire hack so to speak..
The software's originally intended purpose was a hacking tool, but it has since been vastly extended in capabilities. You can even create a Winbin .ecu file entirely from scratch quite easily with it. :)
 

Mick

New member
I have a small problem, is there a way to change the default font and or color for this board on a per user basis? (i.e. user option)
I use a 32" monitor, and the text size is a bit small for my feeble old eyes, although with some contrasting colors the size may be something I can better deal with. I did not see any options like that when I looked over my user preferences, but hopefully I missed some thing?
 

leroy

Donating Member
I don't know of a comprehensive 749.ecu file that is readily available. I made one for promedit a couple of years ago, with just a few of the major tables and posted it at diy-efi incoming. I don't think there has been much effort in this area, since Promgrammer is so cheap, (and good thanks to BillC).

If you know of an updated ecu file let me know.

Thanks.

Jim
 

Mick

New member
Just run the GMPCM software, and load the $58.PCM file. It is basically a HUGE 749.ecu file (along with alot of other features of course). You can then "Export" a Winbin compatible 749.ecu, file, but it would have to be a subset of the $58.pcm file. Since the $58.pcm file has over 500 start address areas defined, you need to filter out about 300 of these.
This filtering is done by unchecking the "Normal" mode box for each item that is not critical to your 749.ecu file. Then you just select "Export" "ECU File" from the menu and voila!!

The SY/TY specific $58 definition can be download directly at the GMPCM website from here.


The software also has the capabilty of importing ECU files, making it very flexible for a wide range of users.
 
B

Blake

Guest
OK. Think I found out what it was. While I am using the GMPCM software, I MUST disable auto protect on my Norton's. I can actually enable Norton's while I am using the GMPCM and begin recreating the runtime errors. Turn off the autoprotect and no problems. Looks like my virus scanning software was interfering with the GMPCM software. Thanks again.
Blake
 

TheObiJuan

Active member
Mick said:
I have a small problem, is there a way to change the default font and or color for this board on a per user basis? (i.e. user option)
I use a 32" monitor, and the text size is a bit small for my feeble old eyes, although with some contrasting colors the size may be something I can better deal with. I did not see any options like that when I looked over my user preferences, but hopefully I missed some thing?

i have a 33" mitsu monitor and have no problem with the font.
what resoltion are you running?
what you can also do is hold down control key and roll the scroll ball in the mouse up. it will increase the size of the font.
the same can be done by going to view-text size-larger in IE
 

Mick

New member
Hey Blake,
Thanks for that heads up!!!
I was not aware that there were issues between the Norton stuff and GMPCM, although I have heard it does this on various other applications. It probably does not like the fact that it includes a live update feature, as several internet related modules are imbedded in the software's code for this purpose.
Anyway, thanks again!! This info can prove invaluable to many who may run into issues such as this. You are both a gentleman and a scholar!!
 

TheObiJuan

Active member
np man.
btw, congrats on making the 3100 turbo! why the 16g (big or reg?)


I am considering a SY/TY as my next project, and this site has proven to be very valuable for research and information.

you are picking a platform that will give you headaches but MUCH
pleasure.
i feel fortunate to be around so many knowledgeable people.
i have learned so much from reading their posts.
and the fact that you know a thing or two about ecm's really helps..
i say welcome to the community man.
 

Mick

New member
The turbocharger I use is a ported TDO5 big16g with a 34mm wastegate flapper, and an 8 degree clip. Its roughly the equivalent of the 17c as far as flow (advertised @ 550 cfm).

I like the Mits. turbo's since they are designed to mount where a turbo is supposed to mount-- directly on the exhaust manifold outlet. That in itself offers many advantages over a crossover mount system.

I run about 14psig of boost, which puts the estimated hp at around 285ish.
The Fiero's light weight and 5-spd manual trans. are another benefit, and probably responsible for the high 12's it pops off on G-tech tests. It is certainly not the fastest car that I have built, but its a blast to drive. :)
I based my engine management system on the Turbo Grand Prix 7727 PCM with $8F code that was of course personally turned specifically for this setup.
The 3100 engine was purchased brand new, then built up with custom Ross forged low cr pistons, Total Seal rings, P&P aluminum heads, copper head gaskets, matched intake, etc.. I went with a 2.5" mandrel bent exhaust that I welded up myself, got to use my mig, so that was fun…
Some of my previous projects included a 91 Mits Eclipse GSX, and a 94 Mits 3000 GT VR4. But, I have come to the realization that I need another truck.. ever tried hauling a Christmas tree with a 2 seater sports car?? :) If I can find a nice truck that can beat up on all my sports cars, I know I will be quite happy with it.

Mick
 
Top