External fuel pump, which brand, what model?

Falco

Donating Member
Howdy,

I'm thinking on a fuel system upgrade, which could serve a good build with around 750HP at the crank. I've searched around, but couldn't find any specific information. What kind of pump should I use? Aeromotive? Which model? On a side note, I guess -8 AN lines should be enough for such a build. That's the size I have on the planned fuel cell, so a pump with this size of ports would be ideal...

TIA,
 

Falco

Donating Member
Thanks guys. I'm all ears, so if you have any experience, pls share with me... :D How noisy is this pump?

Later,
 

Lynn D. Brown

New member
Ext Fuel pump

Ext Fuel pump

Falco,

I used #8 for the fuel hose and I think that's plenty. I have plumbed mine for an external as an Aux. pump which I may do later if I need it.

How did U handle the suction off of the Fuel Tank ? I put in an extra SS line thru the top stock FP hanger.
 

Syclone#892

Member
I have the aeromotive pump along with there filters and regulator, and JS Design fuel rails.
The pump is really loud where I have it mounted which is currently behind the rear bumper. With the truck running you do not hear it nearly as much though.
I went with that pump mainly because of Turbo Tony, it seems those canadians use the best parts all the time.
Tony went with -12 line to a y-block under the driver seat and then to -8 to each rail then -8 from each rail to the regulator, and he used -8 for the return line.
I went with -10 feed and -6 return otherwise I have the same setup as him.
I also bought the aeromotive fuel computer which senses rpm and slows the pump down or speeds it up. I am hoping it will ensure my pump lasts a while.

One thing I wished I would have done is sat down and priced everything out at once and with line you are probably looking at $1500-2500 for everything. Those damn fittings are expensive.

Good luck to you, I have a few pics of the pump and such on my website.
 

Falco

Donating Member
Thanks Guys,

My setup is only in the planning stage. I'll run a fuel cell, which has -8 AN ports, Aeromotive pump with the appropriate Aeromotive filter. I can get these threee things around $500. I doubt that the lineing would take an other $1k to compelte theis setup. Anyway, we will see. The pump and the filter have -10 AN connection, but I guess I'll go -8 AN for both ways...

If the fan question is for me, I'm running a two speed Ford fan from a 95' Taurus 3.8l...

Later,
 

TURBO TY

New member
the aeromotive sunami pump is nice and can support that hores power. also here is a tip, when you run the pump, aeromotive recommends that you use two fuel filters, one on the inlet and one on the discharge. i think their website has all that info on it. hope that helps ya
 

Syclone#892

Member
Falco watch out for the fittings they are expensive :eek:
I paid $6 for -6
$7 for -8
$8 for -10 hose
Then you need hose ends and the fittings for the pump and such. The aeromotive stuff requires o-ring fittings also. You can use regular unions just make sure they do not bottom out and that you have a good o-ring. I used some earls or something o-rings and I had leaks talked to aeromotive and they sent me some of theres and they were twice as thick.
I am also running a cell, triangle enginering aluminum with -10 fittings.
About the fittings some of the -10 hose ends cost like $30 a piece and I needed a few of them etc.
I just wanted my truck to run this year and took some shortcuts and just installed the cell in the bed but since a pretty much have no money since I bought my new truck I am going to do some frame work and make the cell fit under the bed and hopefully make the factory fill tube work again. Fyi my cell would fit perfectly under the bed except for the spare tire crossmember which I am going to remake.

If the fan question was for me
I have the ramchargers fan Brian Green talked about. I have not drove it very much but it sure blows a lot of air and cools it down nicely.
 

ed hess

race or get outta the way
falco

this link shows my cell setup to run dual tanks.

the pumps are dual walbro externals. same specs as what everyone around here puts inot their tanks.

I decided to use 2 in case one fails i dont screw up the motor fom being to lean. As you can see the use of An fittings and SS line can get out of hand real fast.

http://www.sy-ty.com/gallery/view_photo.php?set_albumName=album88&id=Image205

view_photo.php


ed
 

Falco

Donating Member
Thanks guys, great info! I plan to mount the cell under the bed and also plan to use the stock fill tube. Summit has a fast fill adapter for most of the cells. I'm not sure how does it work, but I'll figure out.

Holly setup, Ed! I like it...

Later,
 
Top