fans fuse is blowing.

wildphil

I Love My Ty's
Today, for the third time . I can't have this happening. Need some suggestions.

Would anything cause this besides the fans? After I change the fuse they run fine.

Are the fans seizing after they get hot and blowing the fuse? Then cooling enough to run again by the time I change the fuse?

Has anyone had this happen?
 
Last edited:

Ty#365

BOOST LAUNCH KING
Re: fans fuse is blowing.

Your cooling fans or the heater fan? The motor is probably dying causing too much draw.
 

TYTILIDIE

METH HEAD
Re: fans fuse is blowing.

What fuse do you have in there? What fan? What gauge wire? I have messes around with the Volvo fan and found that you need at least 10ga wire with a MAXI fuse, a good 50-60amp. And have it on a relay.
 

wildphil

I Love My Ty's
Re: fans fuse is blowing.

Its the cooling fan.

It is new. But there could be something wrong with it.

Its a Flex-A-Like dual fan. I think it is suppose to draw 20 amps.

It blew the 20 amp the other day. So I tried a 30 amp. It was a little to much because it melted the fuse holder.

Also then I ran the power wire and ground I used 10 ga. wire.
 

bonesdmz

In Mother Russia Typhoon drives You!
Re: fans fuse is blowing.

Check the datasheet, maybe 20 amps are for single fan, so you need 40 for both.
 

wildphil

I Love My Ty's
Re: fans fuse is blowing.

I am thinking there has to be a problem. The relay is suppose to handle a 40 amp draw fan. and I used 10 ga. wire.
And wouldn't it have blown the 30 amp fuse. And not melt the fuse holder.

Let me know if I am all wrong.
 

bonesdmz

In Mother Russia Typhoon drives You!
Re: fans fuse is blowing.

I am thinking there has to be a problem. The relay is suppose to handle a 40 amp draw fan. and I used 10 ga. wire.
And wouldn't it have blown the 30 amp fuse. And not melt the fuse holder.

Let me know if I am all wrong.

I think you should doublecheck the wiring, fuseholders and stuff, there has to be some connection problem. Clean everything up.
A little voltage drop can easily generate a lot of extra heat and amps.

You can also check the fans directly, just hotwire them to the battery (use good wires!), and use amp meter to check the power draw and how it changes over time.
 

wildphil

I Love My Ty's
Re: fans fuse is blowing.

I think you should doublecheck the wiring, fuseholders and stuff, there has to be some connection problem. Clean everything up.
A little voltage drop can easily generate a lot of extra heat and amps.

You can also check the fans directly, just hotwire them to the battery (use good wires!), and use amp meter to check the power draw and how it changes over time.



I will go over the wiring again. It is all new. But maybe I do have a bad connection.

That amp meter test sounds like a good thing to try also.
 

TYTILIDIE

METH HEAD
Re: fans fuse is blowing.

Phill, if I were you, I'd wire each fan separately with 8ga and a 40-50 amp MAXI fuse. The small ones don't cut it in the long run. Look in the fuse box of late model cars, efans use maxi fuses.
 

nallj92

Active member
Re: fans fuse is blowing.

flexalite 210s say 19.5 amps for both fans being that the single110 take about 9 amps, I would double check good gounds (scrape all paint away). Also a good check would be a ammeter to see what they do pull on startup
 

dgoodhue

BuSTeD 4.3
Re: fans fuse is blowing.

I hope your not using the factory wiring to power those fans. I used a relay connected to the factory wiring. I would also recommend individual fuses. I had one of my flexalite fans die (I bought around 2004) and having one fuse took out both fans and melted the fuse holder on me.
 

JSM

Active member
Re: fans fuse is blowing.

The initial startup amps is much larger than 20 amps for sure. I run self reseting circuit breakers.

Problem I think is your starting 2 fans at the same time through the same wiring. Caspers sells a delay so you can delay the startup of the 2nd fan by a second or so after the first fan is going. Another cheaper option is to run 1 fan all the time, let the 2nd kick in only when you need.
 

wildphil

I Love My Ty's
Re: fans fuse is blowing.

Thanks for the info everyone.

I did install new 10ga wire for the fan. I ran the power directly to the batt. I think the ground also to the batt.

Do you all think if I ran another circuit and added another relay that has the adjustable. Then set them to kick in at different temps.

I thought this may take care of the possable causes.

Would this work?
 
Last edited:

tnsyty

Active member
Re: fans fuse is blowing.

Do you have both of them wired to a switch or to a temp sensor? If they are both wired to a switch, maybe wire one to a switch and pick up one of the E-Fan wiring kits from pepboys that turns the other on at a certain temperature. I put a single fan with the pepboys wiring kit on blazer several years ago, and the current owner still has it wired the same way today.
 

wildphil

I Love My Ty's
Re: fans fuse is blowing.

I went out to take a amp reading on the fan.

Found out my meter only reads to to 10a. I'll have to see if I can find another meter.

I temporarily connected the power wire togather so the fan would run.

With each additional on and off cycling on the fans the copper wire kept getting hotter until I couldent hold on to it. Does wire normally get that hot?

As I was typing this post. UPS delivered.a relay that I had ordered right after the fuse holder melted on the other one.

It is Derale 16759. I will probably get another one and use one for each fan. But I think that I will check the wiring out to see it I can determine what is causing the problem
 

JSM

Active member
Re: fans fuse is blowing.

Heat in a wire = resistance. Either its undersize for load its carrying, or the quality of the wire is junk, or the load is just too high.

You may consider the dodge minivan relays also mounted with minimal source wire lead distance. I posted this relay awhile back, its actually a solid state relay made for running the fans in a dodge minivan.

Won't help the load per se though. How long of a power lead are you running?
 

wildphil

I Love My Ty's
Re: fans fuse is blowing.

Heat in a wire = resistance. Either its undersize for load its carrying, or the quality of the wire is junk, or the load is just too high.

You may consider the dodge minivan relays also mounted with minimal source wire lead distance. I posted this relay awhile back, its actually a solid state relay made for running the fans in a dodge minivan.

Won't help the load per se though. How long of a power lead are you running?


Could be junk wire. I bought it a Auto Zone. The wire is 12 ga 5 to 6 feet long. Run to the battery. I could connect to the alt to cut the distance down. Or run a bigger gauge wire

I looked this afternoon but can't find a meter that will measure more than 10 amps.

I will look for your post on the mini van relay.
 
Top