Fast ecu question. Experts needed.

cjg454ss

Member
When running a classic fast and msd distributor with two wire harness hooked to 6a box what so you connect the fast ecu to? Directions say the 4 wires off the stock computer but the new distributor doesn't have the ignition module.
 

RealFastV6

@jb_and_his_coffee
Re: Fast ecu question. Experts needed.

In your case the distributor is just your crank sensor. So you wire the distributor directly to the FAST, and then FAST fires the 6A through the points output. This is a white wire on my XFI, I don't remember on the classic. The tach signal then comes from the 6A to the dash since you're not using the factory coil.

That make sense?
 

cjg454ss

Member
Re: Fast ecu question. Experts needed.

In your case the distributor is just your crank sensor. So you wire the distributor directly to the FAST, and then FAST fires the 6A through the points output. This is a white wire on my XFI, I don't remember on the classic. The tach signal then comes from the 6A to the dash since you're not using the factory coil.

That make sense?

Yes mAkes sense, do you know which wires from the fast connect to the disty?
 

RealFastV6

@jb_and_his_coffee
The MSD distributor is going to be an Inductive trigger. Look for "Inductive Crank Signal" or maybe just Crank. Is nothing labelled?



Sent from my iPhone using Tapatalk
 

cjg454ss

Member
Re: Fast ecu question. Experts needed.

The MSD distributor is going to be an Inductive trigger. Look for "Inductive Crank Signal" or maybe just Crank. Is nothing labelled?



Sent from my iPhone using Tapatalk

No I believe it's setup to be spliced in. It's labeled but for connecting to the stock ecu.
 

Z SKI

Donating Member
Re: Fast ecu question. Experts needed.

That fool Justin be knowing his FAST shiznit!!!
 

cjg454ss

Member
Re: Fast ecu question. Experts needed.

I had a wire incorrect. I got it running and man does it pull smoother than the stock ecu. Only issue I have now is the idle. It seems the iac is not working at all. When I turn on the ac it doesn't idle up.
 

RealFastV6

@jb_and_his_coffee
Re: Fast ecu question. Experts needed.

IAC is probably working ok if it starts and idles.

There should be a wire for AC in the harness that tells the ECU to increase idle speed for the compressor kicking on. There's also a setting somewhere in the dash, might just be AC Enable I don't really recall. Anything labeled AC or anything about it in the Fast Track Harness instructions?
 

cjg454ss

Member
Re: Fast ecu question. Experts needed.

IAC is probably working ok if it starts and idles.

There should be a wire for AC in the harness that tells the ECU to increase idle speed for the compressor kicking on. There's also a setting somewhere in the dash, might just be AC Enable I don't really recall. Anything labeled AC or anything about it in the Fast Track Harness instructions?

I don't see anything pertaining to a/c, could I connect the stock ecu back to the iac and run both? I see the dot on the fast ecu screen but it doesn't follow the line I'm telling to to.
 

RealFastV6

@jb_and_his_coffee
Re: Fast ecu question. Experts needed.

I don't see anything pertaining to a/c, could I connect the stock ecu back to the iac and run both? I see the dot on the fast ecu screen but it doesn't follow the line I'm telling to to.

No. And I have to be brutally honest with you for a moment here; if your first idea for dealing with the IAC not displaying properly is to hook the stock computer back up and run it in parallel; then this is going to be a very long and very hard road for you right up until you firesale the truck at a loss because you're tired of dealing with it.

What RPM is the truck idling at?
 
Top