First Timer Question (stock turbo removal)

Seti

Member
I’m going to be pulling my stock turbo out in at the end of the week and I’ve never done anything like this before so I’m looking for some guidance. The most I’ve done so far on my Ty myself is changing the spark plugs, wires, dist cap and fluids for tune ups so this is kind of a big undertaking for me.

Does anyone have any “look out for’s” or “make sure you do xyz’s” to suggest?

Much appreciated.

S.
 

Captain Morgan

Moderated User
Re: First Timer Question (stock turbo removal)

I think the best single piece of advice is going to be to purchase a can of PB Blaster and start soaking the 4 nuts on the header flange and the 3 nuts holding the downpipe on. Id hit them all once a day just to help things loosen up, that will make the job a whole lot easier.

I cant remember if the nuts are 14mm, 15mm or 9/16", but make sure you have some good box wrenches cause not all of those can be removed with a socket and ratchet.

Also, removing the inner fender will is pretty much a must when doing this.
 

Seti

Member
Re: First Timer Question (stock turbo removal)

I think the best single piece of advice is going to be to purchase a can of PB Blaster and start soaking the 4 nuts on the header flange and the 3 nuts holding the downpipe on. Id hit them all once a day just to help things loosen up, that will make the job a whole lot easier.

I cant remember if the nuts are 14mm, 15mm or 9/16", but make sure you have some good box wrenches cause not all of those can be removed with a socket and ratchet.

Also, removing the inner fender will is pretty much a must when doing this.


Thanks much. That's the kind of info I'm looking for. Something a person who's never done this before would not have thought of.

S.
 

JSM

Active member
Re: First Timer Question (stock turbo removal)

Good assortment of hand wrenches, stubby, maybe even a claws foot.

Patience is a must. If the nuts have never been off they will be stuck rather well. Add to that some of them are almost impossible to get a good angle on. It will be fun, but with time/patience you will get it.
 

pinellas50

New Guy
Re: First Timer Question (stock turbo removal)

The nuts are 15mm if memory serves. Loosen the bolts on the catalytic converter as well. Those nuts are also a good candidate for PB blaster. You will most likely need to tap/whack the down pipe so it slides further into the cat to get the room necessary to get the turbo out.

Some have said they have to take the upper charge cooler off to get the turbo out. I didn't.
 
Last edited:

sy#2716

SyTy 4 Life
Re: First Timer Question (stock turbo removal)

Also If the pb blaster does not work you will need to get a torch to heat the nuts. Just be careful and do not snap off the stud they are a pain to drill out of the exhaust manifold. You will need to take a fender well out and also you will want to drain the radiator some becasue if not you will have coolant all everywhere.

Make sure you have a bag to put everything so you do not loose stuff.
 

Don W.

Stab it and steer it
Re: First Timer Question (stock turbo removal)

An old trick, not yet mentioned, with frozen nuts is get a big punch and sledge and just whack one of the flats on the nut a few times. This can help and is safer than heat. Still no workie? Then get the heat. PB Blaster first is the key though.
 

SY2932

Administrator
Re: First Timer Question (stock turbo removal)

A 15MM deep well socket will come in handy on the nuts that hold the turbo to the exhaust manifold. I had to tap the back of the socket on with a hammer when I removed my stocker. Removing the wheel well is highly recommended. Other than that, the "double wrench trick" (where you interlock the open end of one wrench into the box end of another for additional leverage) will make things easier. As mentioned by EVERYONE else, hit everything with penetrating oil a few days before you tackle it. To make things easy on yourself, loosen the oil and water lines before you cut it completely loose. HTH's.
 

Seti

Member
Re: First Timer Question (stock turbo removal)

Much appreciated all! I'm picking up the Blaster today after work. Seem's like this is goig to be more work than I thought but I'm sure it will be worth it.

S.
 
Re: First Timer Question (stock turbo removal)

if pb doesn't work, try some brake fluid on the frozen bolts. i've seen it work far better than any penetrating lube before. believe it or not, it works. i have a spray 9 bottle filled with it :tup:
 

Seti

Member
Re: First Timer Question (stock turbo removal)

if pb doesn't work, try some brake fluid on the frozen bolts. i've seen it work far better than any penetrating lube before. believe it or not, it works. i have a spray 9 bottle filled with it :tup:


Good to know. I have break fluid on hand. :tup:

S.
 

Ry368

one mile = 5280 feet
Re: First Timer Question (stock turbo removal)

You'll learn how to "double wrench" really quick.:tup:
 
Top