FMIC pics needed please.

13.robb

13.robb

New member
I have deleted the factory water to air intercooler set up due to a bad pump, I am going to install an air to air set up, I was wondering if anyone has any pictures of a finished install.
I must be able to keep the a/c operational, i live in vegas and drive almost everyday. Thanks. Robb
 
nallj92

nallj92

Active member
Re: FMIC pics needed please.

i have some ill get up later.. just put it in last week W/AC and all

edit. heres the pics, went with the ebay core, the 3 inch thick one, with a pipe, kit.
couple things, i left about a finger width between the core and the a/c , it cools it great with a taurus 2 speed fan, the pipes were close to the crank pulley but will work. I had to notch the latch frame to fit. ditched the PS cooler and reloated trans cooler to underside of frame behind driver seat with a fan. i cleaned up and edged the steel with some vac line so it was a bit nicer. i had to trim the bottom corner edges of the grill to fit the core, it looks nice and is not even noticable.

weight- 40 lbs of water to air stuff, and 20 lbs of are to air, so about a 20 lb loss of weight, which i like.


n6601292_31386824_3227.jpg

n6601292_31386827_4025.jpg

n6601292_31386829_4565.jpg

n6601292_31386831_5130.jpg

n6601292_31386832_5409.jpg

n6601292_31386833_5693.jpg

n6601292_31386836_6546.jpg
n6601292_31386838_7127.jpg

n6601292_31386839_7427.jpg

n6601292_31386840_7731.jpg
n6601292_31386841_8031.jpg
n6601292_31386843_8632.jpg
n6601292_31386844_1593.jpg
 
Last edited:
13.robb

13.robb

New member
Re: FMIC pics needed please.

Thanks for the responses, i checked out epix's, my internet blocked maitai's, looks very effecient, on epix's were you able to keep the a/c?
 
skwayb

skwayb

NWSTP
Re: FMIC pics needed please.

nallj92 said:
bump for my uploaded pics above.....
Click to expand...

I pretty much followed Epix setup.

Man mine looks so similar to yours Nallj92... except I have 3" Tubes.

DSC02474.jpg


DSC02470.jpg


DSC02469.jpg


A2A11.jpg


A2A7.jpg


A2A8.jpg
 
nallj92

nallj92

Active member
Re: FMIC pics needed please.

paul, mine is 3 inch pipe also, i modeled mine a bit after yours, but had to fit it different for my AC hoses and heater box! your engine bay does look good! when are we going to see some numbers from the truck?
 
skwayb

skwayb

NWSTP
Re: FMIC pics needed please.

Thanks TYTILIDIE. Some of it was done by the original owner but I have done a lot of work to keep it look as good as he did if I made any changes like the A2A.

I am going to the Turbo Thunder Event in July so I should hopefully have some numbers then. I still have a lot of tuning to do and get it to pass emissions. It fails the idle part. Tried all kinds of things and it just barely fails. Have a few more things to try to get it to pass.

Don't expect the world out of it. It is a stock motor (heads, cam, pistons, rods, etc.) I am hoping I can get it in the mid to low 12's if I am lucky. But since I haven't ran it yet I am thinking high 12's is all I will get out of it until I get kinks worked out. (Tranny tuning, Wastegate adjustment, methanol tuning, etc...)
 
MAITAI1993

MAITAI1993

DON'T MAKE ME SLAP YOU.
Re: FMIC pics needed please.

TYTILIDIE said:
Your truck makes me sick Paul :lol:
Click to expand...
sick like puke :sick: pauls truck is ok I guess if you dont wann cut the core support out do like I did 2.5 inch pipe you are not gonna gain shit out of 3 inch unless you have a huge turbo and still wont notice shit

here




 
skipztt

skipztt

boost
Re: FMIC pics needed please.

MAITAI1993 said:
sick like puke :sick: pauls truck is ok I guess if you dont wann cut the core support out do like I did 2.5 inch pipe you are not gonna gain shit out of 3 inch unless you have a huge turbo and still wont notice shit

here




Click to expand...





:tup: good job MAITAI1993!!!

thats the way i was gonna do a fmic, if i decided to go that way. but i decided to keep the stock ic stuff.
 
MAITAI1993

MAITAI1993

DON'T MAKE ME SLAP YOU.
Re: FMIC pics needed please.

skipztt said:
:tup: good job MAITAI1993!!!

thats the way i was gonna do a fmic, if i decided to go that way. but i decided to keep the stock ic stuff.
Click to expand...
thanks I try
 
You must log in or register to reply here.
Top