fuel injection question

gringo76

New member
are these syclones bank firing the injectors. like firing all three on one side and then all three on other side ? didn't think they are sequential ? trying to pin point a miss at idle. I put turbo tweak chip,42lb injectors,and 3 bar map and set fuel pressuer at 43 with line disconnected pure there instructions and she skips. if I put pressure up to 48-50 about 90% of skip goes away making me think its fuel related. have not gone further with fuel pressure., any clues guys? I have not got my datamaster working yet as I am waiting on access codes for it.
 

Eric Sy GN

Donating Member
Re: fuel injection question

Correct, they all fire at the same time.

Once you get the datamaster working, take a log and post it. It might be too lean, but the computer will compensate and add fuel, which we would see in the BLM reading.
 

gringo76

New member
Re: fuel injection question

Correct, they all fire at the same time.

Once you get the datamaster working, take a log and post it. It might be too lean, but the computer will compensate and add fuel, which we would see in the BLM reading.

when you say all together, do you me all one bank or all six at same time ?
 

gringo76

New member
Re: fuel injection question

All six at the same time.

wow, that can't be efficient lol, but I guess for 91 not bad. I wounder how much these trucks would pick up with some sort of sequential fuel injection, like big stuff ect.
 

gringo76

New member
Re: fuel injection question

all right guys, got datamaster working. the issue I am having is at idle when you rev it and let it come back down to idle, it will go lean for about 5-10 seconds, start to miss and slowly recover and all is good again. its idling at 14.5-15 a/f normally and when you rev it and let it go back to idle its 16.8-17 a/f for 5-10 seconds and skips. only thing I see following this in data master is map reading. normally its about 26 and when you rev it and let idle again it goes to 30 and as it works its way back down to 26 it richens up and skip goes away. idle pos is at 0, idle rpm is at 825 but rpm is at 900, didn't know if these need to match? any thing else I need to be looking at? oh and this is with fuel pressure up at 52lbs with line disconnected, at 43lbs its bad all the time at idle
 

gringo76

New member
Re: fuel injection question

Correct, they all fire at the same time.

Once you get the datamaster working, take a log and post it. It might be too lean, but the computer will compensate and add fuel, which we would see in the BLM reading.

I see the blm enable in top right box and is lite up yellow with a number 1 beside it at idle , as soon as you come off idle it goes green and 0.
 

jeepruby04

New member
Re: fuel injection question

The symptoms would indicate a vacuum leak. IAC at zero, idle above commanded, and you increasing fuel pressure to compensate the rough idle due to the lean condition.
 

Eric Sy GN

Donating Member
Re: fuel injection question

With my chip, it is designed to have the IAC reading up around 30 (warmed up, in park). Yours is at zero, so either there is a vacuum leak, or you need to adjust the throttle stop screw (min air opening). You would need to close the throttle blade slightly (turn the screw counter-clockwise), the computer will respond by increasing the IAC steps.
Get that straightened out and see how it goes.
Regards,
Eric
 

gringo76

New member
Re: fuel injection question

The symptoms would indicate a vacuum leak. IAC at zero, idle above commanded, and you increasing fuel pressure to compensate the rough idle due to the lean condition.

thought that too but all new vaccum lines and intake gaskets, I have checked several times
 

gringo76

New member
Re: fuel injection question

With my chip, it is designed to have the IAC reading up around 30 (warmed up, in park). Yours is at zero, so either there is a vacuum leak, or you need to adjust the throttle stop screw (min air opening). You would need to close the throttle blade slightly (turn the screw counter-clockwise), the computer will respond by increasing the IAC steps.
Get that straightened out and see how it goes.
Regards,
Eric

thanks I will give that a try. thanks for your help,i have had this truck for about a month and its my first syclone and trying to straighten out losts of previous problems, I'am sure its not your chip but miss adjusted stuff. I'am just use to mustangs and learning on these. thanks
 

gringo76

New member
Re: fuel injection question

after about 5-10 seconds the iac pos will be at 0 and rpm at 900 and af at 14.5-15.0. I will try to adjust throttle blade and report back
 

BMFB

Not to scale
Re: fuel injection question

I've been driving and tuning these trucks for years now and never had to adjust an idle screw. I would never touch one.
 

gringo76

New member
Re: fuel injection question

I've been driving and tuning these trucks for years now and never had to adjust an idle screw. I would never touch one.

ya my thoughts too, unless previous owners before me messed with it, then I got to fix, so I need to check
 

gringo76

New member
Re: fuel injection question

all right I set the idle, tps per one of the links on here. put wire between pin a&b and turn key on to get iac to fully extend and then unplugged it. turn key off and removed wire. started truck and set base idle at 475-500 in drive. turned truck off and reconnected iac. turn key on and set tps to .62(this is as low as I could get). cranked truck up and adjusted my fp down to 43lbs from 53lbs with line disconnected. idle pos is now at 90 and slowly dropping were before it was at 0. I guess it needs to be driving for 20-30 mins to get idle pos to settle down to around 30? as far as the way the truck acts it appears its all fixed. rev's good, and does not go lean after reving it, all the skip at idle after reving is gone too. heres a snap shot.
 

gringo76

New member
Re: fuel injection question

not sure on the knock readings, I guessing from all the adjusting at low rpms and so forth? after everything was set I reved the snot out of it and didn't increase it any more.
 

gringo76

New member
Re: fuel injection question

after I ran for few mins turned off and recrancked. looks better to me, what yall think. iac pos at 31!
 
Top