fuel injection question

gringo76

New member
Re: fuel injection question

knock still weird. is it due to cranking. after its running I don't see it move. is there anyway to zero it out after its running or just remember that count and add from there once your driving it?
 

gringo76

New member
Re: fuel injection question

With my chip, it is designed to have the IAC reading up around 30 (warmed up, in park). Yours is at zero, so either there is a vacuum leak, or you need to adjust the throttle stop screw (min air opening). You would need to close the throttle blade slightly (turn the screw counter-clockwise), the computer will respond by increasing the IAC steps.
Get that straightened out and see how it goes.
Regards,
Eric

so what you think of my last datamaster snap shot. am I on the right track?
 

Eric Sy GN

Donating Member
Re: fuel injection question

It looks like you are on the right track.

One thing that concerns me is that the TPS is at 1.6% (I assume your foot was off the throttle). The TPS autozero's at key on and should be 0.0-0.4% which the throttle closed, which could mean your throttle blade is moving when you start the car due to vacuum (loose shaft). It also could mean something is binding and not allowing it to return to the fully closed position after you've been on the gas.

By not returning to zero, it affects what BLM cell its in, and affects commanded idle speed, and some other small things.

It's possible you might need to tweak the IAC again once you get the TPS thing fixed.

Regards,
Eric
 

gringo76

New member
Re: fuel injection question

It looks like you are on the right track.

One thing that concerns me is that the TPS is at 1.6% (I assume your foot was off the throttle). The TPS autozero's at key on and should be 0.0-0.4% which the throttle closed, which could mean your throttle blade is moving when you start the car due to vacuum (loose shaft). It also could mean something is binding and not allowing it to return to the fully closed position after you've been on the gas.

By not returning to zero, it affects what BLM cell its in, and affects commanded idle speed, and some other small things.

It's possible you might need to tweak the IAC again once you get the TPS thing fixed.

Regards,
Eric
Thanks I will check into that and see what's going on there. At least on going the right direction. Thanks again these little tips and settings really helping me out in trying to get this thing right.
 

TYTILIDIE

METH HEAD
Re: fuel injection question

It looks like you are on the right track.

One thing that concerns me is that the TPS is at 1.6% (I assume your foot was off the throttle).

X2 on that

Another note. it is very common for knock counts to appear at start up, they are relitively meaningless.

Also, I am not sure if it is an altitude thing but all the trucks I have ever worked on that have AFPR's need to be set at 50psi to run normal for whatever reason.
 

gringo76

New member
Re: fuel injection question

It looks like you are on the right track.

One thing that concerns me is that the TPS is at 1.6% (I assume your foot was off the throttle). The TPS autozero's at key on and should be 0.0-0.4% which the throttle closed, which could mean your throttle blade is moving when you start the car due to vacuum (loose shaft). It also could mean something is binding and not allowing it to return to the fully closed position after you've been on the gas.

By not returning to zero, it affects what BLM cell its in, and affects commanded idle speed, and some other small things.

It's possible you might need to tweak the IAC again once you get the TPS thing fixed.

Regards,
Eric

on adjusting this, I have tried to get my tps volts down but could only get down to .62 before I ran out of adjustment hole and I see .50 is what you try to get. I take it if I get tps volts down the tps% will also go down. in the mustang world I would allway just slot the holes a little to get my adjustment. is that how syclones guys do it too? or are these two diff readings, one the sensor and one the shaft pos?
 

gringo76

New member
Re: fuel injection question

oh one more thing. does it just need to be at .0-.4 at key on or idle too. I looked at throttle body when I had I off and everything looked tip top but I will recheck.
 

gringo76

New member
Re: fuel injection question

think I got it. throttle blade must be slightly worn. I can play with it and watch dm and tps % will jump from 0.0 to .4 but looks like I might of got it. another thing I found was a bad fuel pressure gauge. I had a very old cheap one and the one I ordered from rpm to mount on fuel rail showed up, so got that pegged down at 43lbs. also found fuel lines vibrating around frame rail. see what you think eric
 
Top