HELP understanding datamaster

gjp

another post whore
I just got my cable. I used a SIIG usb to serial adaptor with no problems (30$ at fry's, could not wait for e-bay). I took the truck out for a little run to see how it works. I only took it to 60mph wot. What should I look for, good or bad?? I thought It did fuel pressure but I dont see it? any help will be great, thanks.
 

0260IN3

Engine Builder
Re: HELP understanding datamaster

A good tune will show 0 knock retard and 02 millivolts in the 800 - 900 range. It's not common to see a coulpe degrees of retard on shifts. Log some stuff and go home and look it over. The more times you log and look over stuff the more you will understand, and ask lots of questions, that's how you will learn.

Besides that, there a million other things that you could go on and on about forever.

Those items above ensure it will live for a long time

Mark
 

gjp

another post whore
Re: HELP understanding datamaster

the retard hit 6 max and was 3.2 at 60mph, advance was 9.5 and the o2 was 1048. My spark advance is 24 at idle. I am only running 13.7 boost via boost controler untill I get it comfortable running more. also It only builds no boost at 2000 rpm with the brakes on. do I need to rev higher for a better boost launch or hold it longer then a few seconds or should there be boost?? thanks.
 

gjp

another post whore
Re: HELP understanding datamaster

sorry looked at it again I build 3.4 lbs of boost at 2300 rpm before the launch
 

gjp

another post whore
Re: HELP understanding datamaster

Went to fry's. I hate it there but they had what I needed. Its a SIIG inc. usb to serial adapter. usb 1.1 to 9 pin serial. It came with a cd. when I pluged it in windows noticed new hardware. I installed 2 drivers it asked for. Hooked up the datacable and pluged it in. Set the datamaster to the correct com port and I worked. Suprised I had no problems. There was a cheaper one there for 15$ but this one had a 6 foot cable compared to 2 ft. It was 30$ but it worked.
http://www.siig.com/product.asp?pid=252&catid=36
 

0260IN3

Engine Builder
Re: HELP understanding datamaster

gjp said:
the retard hit 6 max and was 3.2 at 60mph, advance was 9.5 and the o2 was 1048. My spark advance is 24 at idle. I am only running 13.7 boost via boost controler untill I get it comfortable running more. also It only builds no boost at 2000 rpm with the brakes on. do I need to rev higher for a better boost launch or hold it longer then a few seconds or should there be boost?? thanks.

Not bad. If the tune was a little richer (900mv O2) you would most likely see less, or no knock. To build more boost to launch, put the truck in neutral and with one foot on the brake and one on the gas, Rev the engine once to about 3000 rpm and as the rpm's come down the engine has more vaccum and the brakes will hold better (push on the pedal hard when you rev the engine) Then put it back in gear and try to make more boost. You should be able to get more than 3 psi, mabey 7-8 psi. The next option is a looser converter.
 

gjp

another post whore
Re: HELP understanding datamaster

What fuel pressure should I be at. I know to disconect vaccume line and check. I have stock injectors with a 255 pump and AFPR. I dont have a guage yet. The sy was not slipping the brakes. I am just not shure how hard I can rev the engine before things let go. I will hold the brakes and rev the engine to about 2300-2500 rpm for a second then let off the brakes while I give it gas. According to the reading it went 0-60 in 4.73 seconds with 13.7 boost. I got the truck with a new street/strip rebuilt trans and a 2300 convert. Except for a few weird things the engine does when its warm it runs good. I am also stuck with 91 octane fuel. I will be adding alcohol soon to help with the wot kr.


BTW, thanks for the input. Anything else I should look at. I hope to do a 1/4 mile run next weekend to get a better idea. I just want to make sure I dont blow it up. I have yet to push this truck. I dont think I have even gone over 100 in it yet.
 

gjp

another post whore
Re: HELP understanding datamaster

thanks I searched but must have missed that. good reading.
 

mrweelr

New member
Re: HELP understanding datamaster

GJP - you want to see O2 Mv values between 900-1000. Sounds like you're running a bit rich at WOT, but with 91 octane, that's on the safe side. You could back your base fuel pressure down a bit to lean it out some, but keep a close eye on the KR value. I'd lose the ATR chip and go with an Ultimate or Phil Long chip, depending on what injectors you have. LIVE1053RULZ and I are over in Santa Clara if you want help tuning your truck. BTW, thanks for the tip on the USB-to-Serial converter; I was going to buy a USB Datamaster cable to replace my serial cable until I saw this. That'll save $60 :)
 

gjp

another post whore
Re: HELP understanding datamaster

Right now I am running the stock chip. I will get a chip soon.?? Whats the best for the price? the injectors were replaced by origional owner about 20k ago. Not sure what they are. I guess stock. would 50's make a difference on a stock motor and turbo? I would like to get together one day and tune and bs.
Also is there a gas you find better than others. I run chevron but have been using 76 because of my work gas card. That run was on 76. Does octane boost help. My sy still stumbles idle when warm. all the problems happen after I drive for over 20 min. Before that it runs perfect. after that it searches for idle and the rpm jumps while cruzing on the freeway. Thanks. I will run a datamaster when the problems occur to se what is going on. Sucks I only get 20 runs on the thing. how much to buy it?
 

mrweelr

New member
Re: HELP understanding datamaster

Lot of questions there. Shoot me an e-mail at the end of the week and we can talk shop or meet up. I run Chevron, 76, or Shell 91. You can add Xylene to your tank if you want to boost the octane. I am running alky injection with 17.5psi of boost on 91 octane. This is a safe tune for me on the street. I've been thinking about trying some of that Torco octane booster, but haven't gotten around to it yet. Based on what you said, your truck needs some TLC. You don't need to buy Datamaster, I'll explain offline.
 

cameronsclone

New member
Re: HELP understanding datamaster

mrweelr said:
Lot of questions there. Shoot me an e-mail at the end of the week and we can talk shop or meet up. I run Chevron, 76, or Shell 91. You can add Xylene to your tank if you want to boost the octane. I am running alky injection with 17.5psi of boost on 91 octane. This is a safe tune for me on the street. I've been thinking about trying some of that Torco octane booster, but haven't gotten around to it yet. Based on what you said, your truck needs some TLC. You don't need to buy Datamaster, I'll explain offline.
Watch out for Xylene. If you get it on your skin or if you're around it for a while it will go through your pores and you won't be able to move or anything. It can make your muscles all numb. A guy I knew had it on a roof and was waliking on it for a few hours and while he was driving home an hour later he couldn't feel his legs or arms and was practically paralyzed. He had to roll to his front door like a log.
 

TYTILIDIE

METH HEAD
Re: HELP understanding datamaster

Also pay attention to IAT's. Yeah 1000mv is way I would say. What kind of jumping is your tach doing on the freeway? Is it flutter? If so maybe its time for a tune up. ALso, looking at your mods I dont see any reason why your trucj wouldnt be able to hold a full 15 psi at the line. I have very similar mods to you and I can hold and launch with 15. Does you ATR exh have a muff? If so Ild say ditch it. I noticed my biggest improvment when I got 3" out the back with a highflwo CAT and no muffler.
 

gjp

another post whore
Re: HELP understanding datamaster

Thanks for the info. How does it sound with no muff? My friend works at a muffler shop and I was thinking about ditching it but I don't want it to sound funny. the tach with jump up 200-400 rpm and will make the truck jerk slightly. I found out I have a bad leak in my TB. I know most leak a bit but I can blow into the tube and it will escape as fast as I can blow. it sounds bad. could be my boost problem to. I can only hold a max of 5-6 lbs at launch and my wot boost will vary from 13-16 lbs even with my controler.
 

TYTILIDIE

METH HEAD
Re: HELP understanding datamaster

Yeah I would get that fixed for sure. My truck sounds pretty beefy w/o the mufff. I like it alot. I do get complaints from the old peeps at my Mom and dads place but I dont really care. I had a Vette with a built motor that I had headers and emptied out to two dual chamber Flowmasters and compared to that the TY is pretty damn quiet.
 

gjp

another post whore
Re: HELP understanding datamaster

my el camino and 57 bel air are loud too. Too loud. I wish I could hear a sound file. for now I will leave it on till I fix my truck. The atr is still not welded so I could remove it to see how it sounds.
 
Top