Help with a Datamaster file?

raman117

Member
Hey guys, I did some runs with Datamaster hooked up, and found some fairly high knock. Here is what I was running and mods:

- Walbro fuel pump
- Wrapped intercooler
- Heat exchanger rerouted to in front of the radiator
- Intercooler pump wired on all the time
- Adam's silicone vacuum kit
- New plugs, MSD wires, cap rotor
- 91 Octane (best gas available up here)

I spoke to Dig last year, and he said the wastegate may be mis-adjusted. I'd like to get this fixed up this year, and I know his PM box is always full. Anyone else have any insight?

ef0YA.png


Here is the full DM: http://www.filedropper.com/5-23-2010
 

WyoSyclone

Active member
Re: Help with a Datamaster file?

I'll take a look at the whole log tomorrow when I'm back in the shop. Besides the KR, it doesn't look bad. What brand of gas are you using??

If you're starting off with the basics, I would:
1) verify the TDC mark on your harmonic balancer with TDC (make sure the ring hasn't slipped).
2) check the timing
3) If you haven't already, pull the plugs and see what brand/heat range they are.
4) Have someone lightly power brake the truck and check the motor mounts.
 

raman117

Member
Re: Help with a Datamaster file?

I'll take a look at the whole log tomorrow when I'm back in the shop. Besides the KR, it doesn't look bad. What brand of gas are you using??

If you're starting off with the basics, I would:
1) verify the TDC mark on your harmonic balancer with TDC (make sure the ring hasn't slipped).
2) check the timing
3) If you haven't already, pull the plugs and see what brand/heat range they are.
4) Have someone lightly power brake the truck and check the motor mounts.

Thanks for the tips, I'll check timing tomorrow after work. Could you explain item number 4 a bit?
 

WyoSyclone

Active member
Re: Help with a Datamaster file?

Thanks for the tips, I'll check timing tomorrow after work. Could you explain item number 4 a bit?

Have someone get behind the wheel, engine running, E-brake and foot hard on the brake. Put truck in gear and just slightly give it some throttle.

Watch the motor... If you have a motor mount problem, the left side of the engine will lift up. I would think that anything over 3/8" would indicate a motor mount problem (worn out).... maybe some other guys will chime in verifying if that amount of movement is about right.

Hope this helps.
 

raman117

Member
Re: Help with a Datamaster file?

Have someone get behind the wheel, engine running, E-brake and foot hard on the brake. Put truck in gear and just slightly give it some throttle.

Watch the motor... If you have a motor mount problem, the left side of the engine will lift up. I would think that anything over 3/8" would indicate a motor mount problem (worn out).... maybe some other guys will chime in verifying if that amount of movement is about right.

Hope this helps.

Oops, I should have clarified my question a bit more. What is the purpose of power braking the truck to check for bad motor mounts (with regard to my knock problem)? Would a bad motor mount contribute to false knock?
 

WyoSyclone

Active member
Re: Help with a Datamaster file?

Oops, I should have clarified my question a bit more. What is the purpose of power braking the truck to check for bad motor mounts (with regard to my knock problem)? Would a bad motor mount contribute to false knock?

Yup, it could cause false knock... your DM run is a little strange in that the KR shown in the first part of the screen capture looks like KR from the tune, but KR shown towards the right side almost looks more like something causing false knock (motor mounts, downpipe, fuel lines, etc.).
 

Petesgn

Member
Re: Help with a Datamaster file?

on the DM file it say the injector duty cycle is 103 , isnt that too high ?
 

raman117

Member
Re: Help with a Datamaster file?

Yup, it could cause false knock... your DM run is a little strange in that the KR shown in the first part of the screen capture looks like KR from the tune, but KR shown towards the right side almost looks more like something causing false knock (motor mounts, downpipe, fuel lines, etc.).

I got under the truck last night, and my exhaust pipe going into the muffler has separated from the muffler, so that might be causing some false knock readings. Ideally, should the knock count be zero and the KR be less than 3-4 for a good running truck?
 

WyoSyclone

Active member
Re: Help with a Datamaster file?

I got under the truck last night, and my exhaust pipe going into the muffler has separated from the muffler, so that might be causing some false knock readings. Ideally, should the knock count be zero and the KR be less than 3-4 for a good running truck?

Knock count won't read 'zero' due to a change made in one of the DM revisions (from Tooky at PowerTunePlus). How much KR you have is what matters... ideally zero, but usually not obtained at all times.
 

raman117

Member
Re: Help with a Datamaster file?

Knock count won't read 'zero' due to a change made in one of the DM revisions (from Tooky at PowerTunePlus). How much KR you have is what matters... ideally zero, but usually not obtained at all times.

Ok. I'll check the timing tonight and let you know what I find. Also, is there any advantage to having Nolan do a custom tune for me? I am looking for reliability above all else.
 

turbodig

Active member
Re: Help with a Datamaster file?

I looked at it a bit, and I'd have to agree with Rob - looks like you have a "clunk" happening on shift or torque events. Exhaust, motor mounts, fuel lines clanking on the trans case, etc.

I don't look at KR as much as counts, in these cases. Where the counts increase is as valuable as how much. In your case, the counts increment mostly at shift pulldowns and at launch. This generally points to a "moving engine" style clunk. Could be actual knock, load related, but you have cases where the counts move where there isn't peak load.

Try an engine tie-down, see if it helps.


Also, while it's hard to tell from a stock o2, you have a lean-out going on right at launch. Was there more than 1/4 tank in it?

If the fuel sat over the winter, run it all out before re-testing. Don't put more good gas on top of the old gas, run as much out as you can and fill up with fresh. Maybe pick a different station.

Aren't you up by Duluth? There's supposedly 93 here:
BP - 19th W and Superior St. in Duluth

Later,
 

raman117

Member
Re: Help with a Datamaster file?

I looked at it a bit, and I'd have to agree with Rob - looks like you have a "clunk" happening on shift or torque events. Exhaust, motor mounts, fuel lines clanking on the trans case, etc.

I don't look at KR as much as counts, in these cases. Where the counts increase is as valuable as how much. In your case, the counts increment mostly at shift pulldowns and at launch. This generally points to a "moving engine" style clunk. Could be actual knock, load related, but you have cases where the counts move where there isn't peak load.

Try an engine tie-down, see if it helps.


Also, while it's hard to tell from a stock o2, you have a lean-out going on right at launch. Was there more than 1/4 tank in it?

If the fuel sat over the winter, run it all out before re-testing. Don't put more good gas on top of the old gas, run as much out as you can and fill up with fresh. Maybe pick a different station.

Aren't you up by Duluth? There's supposedly 93 here:
BP - 19th W and Superior St. in Duluth

Later,

Thanks Dig, you know it's funny you mention about having a clunk at shift points. I believe I may have a bad drivers side torsion bar mount, as whenever it shifts hard or I go over a bump, I hear a pronounced "clunk". It almost sounds like an "oil canning" snap sound, but obviously I don't have any tears in my floorboard sheetmetal. It is RIGHT underneath my feet on the drivers side, I can feel it a bit when it happens.

The fuel was brand new 91 octane, with 3/4 of a tank. Last night, I put about 4 gallons of E-85 into an almost full tank. I was going to try another DM run but did not get a chance to do it. Is there any value in doing that at this point, or do all signs point to false knock? I did not realize the BP on 19th had 93 octane, thanks for the heads up!

Lastly, is there any benefit to running Alky on a stock motor with a slightly custom tune? I'm not looking to race this, I just want to maintain reliability as much as possible. I've read that an AFPR is a must, and I plan on purchasing one of those very soon.
 

turbodig

Active member
Re: Help with a Datamaster file?

Thanks Dig, you know it's funny you mention about having a clunk at shift points. I believe I may have a bad drivers side torsion bar mount, as whenever it shifts hard or I go over a bump, I hear a pronounced "clunk". It almost sounds like an "oil canning" snap sound, but obviously I don't have any tears in my floorboard sheetmetal. It is RIGHT underneath my feet on the drivers side, I can feel it a bit when it happens.

The fuel was brand new 91 octane, with 3/4 of a tank. Last night, I put about 4 gallons of E-85 into an almost full tank. I was going to try another DM run but did not get a chance to do it. Is there any value in doing that at this point, or do all signs point to false knock? I did not realize the BP on 19th had 93 octane, thanks for the heads up!

Lastly, is there any benefit to running Alky on a stock motor with a slightly custom tune? I'm not looking to race this, I just want to maintain reliability as much as possible. I've read that an AFPR is a must, and I plan on purchasing one of those very soon.

I wouldn't run more than 2 (maybe 3) gallons of E85 in with the full tank of gas, unless the tune was set up for that.

E85 would run well for you, but you'd need a bunch of fuel system mods to do it reliably, long term. Especially where we live. If you do that, you'd want a regular gas tune as well for the times you weren't running it.

Don't know about the 93 octane thing for sure. I googled '93 octane duluth mn' and one of the subie forums mentioned it.
 
Top