Help with getting 100% TPS

ZR1TR

New member
I finally got my ALDL cable so I could use Datamaster and I can't get 100% TPS. Best I've seen is about 96%. I have a stretched throttle cable and took out the slack using the fishing weight trick I found on here. Still can't get the throttle body to open all the way with the pedal. If I manually do it under the hood the TPS voltage goes above 4.5. I can't take out anymore slack or it will idle too high.

I thought about bending the gas pedal, but then thought better of it. Any advice on how to approach this?
 

blacktyaffair

Donating Member
Re: Help with getting 100% TPS

I finally got my ALDL cable so I could use Datamaster and I can't get 100% TPS. Best I've seen is about 96%. I have a stretched throttle cable and took out the slack using the fishing weight trick I found on here. Still can't get the throttle body to open all the way with the pedal. If I manually do it under the hood the TPS voltage goes above 4.5. I can't take out anymore slack or it will idle too high.

I thought about bending the gas pedal, but then thought better of it. Any advice on how to approach this?

Bending the pedal works but don't do it with the pedal installed in the truck. The pivot for the gas pedal is plastic and may break if you just pull up on it.
 

Syclone22

Member
Re: Help with getting 100% TPS

You can also install a small washer or nipple
at the back of the throttle cable in cabin but
check first how much clearance your pedal
has to the floor ..
 

ZR1TR

New member
Re: Help with getting 100% TPS

There is a tiny bit of adjustment with the TPS mount but I doubt it's enough.

Here's what I did, been working well for years. Looks weird but, in effect it shortens the cable a bit.

Look at post 10 here:

http://www.syty.net/forums/showthread.php?t=14823&highlight=throttle

Don thanks for the link. :tup: I managed to use some rubber hose to fit around the cable and it did the trick. I don't know how long that will last but I should work until I can find a more permanent solution. I'll try to post some pics later.
 

ZR1TR

New member
Re: Help with getting 100% TPS

Bending the pedal works but don't do it with the pedal installed in the truck. The pivot for the gas pedal is plastic and may break if you just pull up on it.

I figured as much. I didn't want to wind up with the pedal in my hand and do even more damage. Any help on how to remove the pedal?
 

alwayscode390

pppssssshhhhhtttttttttttt
Re: Help with getting 100% TPS

Im going to guess that the throttle cable is irreplaceable, and that is why everyone is using band-aids to fix this issue?

Sorry for my ignorance, I am just making sure I am understanding this correctly :) ---
 

Don W.

Stab it and steer it
Re: Help with getting 100% TPS

I figured as much. I didn't want to wind up with the pedal in my hand and do even more damage. Any help on how to remove the pedal?

IIRC, I think, 3 studs on a bracket where the pedal hinges. I would definitely pull the whole thing and bend it outside the truck. Although others seem to have done it while still in the truck.
 

blacktyaffair

Donating Member
Re: Help with getting 100% TPS

Im going to guess that the throttle cable is irreplaceable, and that is why everyone is using band-aids to fix this issue?

Sorry for my ignorance, I am just making sure I am understanding this correctly :) ---

I was told the throttle cable could still be ordered through Dorman. I was never given a part number but was told a good autoparts person could look it up and find it. I used the cable from my '91 corvette when the cable in the ty broke. The C4 cable was a little long but works after bending the pedal up a little bit. I don't remember if it's three nuts or three screws to remove it either way it's easy. Once removed chuck it in a vise and bend it a little at a time.
 
Last edited:
Top