hunting idle

#2875

built, not bought
i have been working on this problem for a while now and thought i might see what you guys have to offer. basically my truck idles shitty after warmup. here is what i know:

1 leakdown check was good on all 6
2 boost leak check good, am leaking a little around the throttle shaft but not enough to cause a problem plus the tb is new, vacuum is about 17.5-18 at idle
3 a/f mixture is perfect datalogged on the dyno (ultimate chipped (vortec, 412, 50#ers))
4 valve timing is perfect, cam is on standard tooth, not adv or ret.
5 spark timing is perfect
6 i set the idle screw using a procedure i found here. unplug iac, connect pins, blah blah you guys know the drill
7 motor is fresh, i have all new sensors (no egr) multiple spark box, hot coil, ngks gapped to about 32

is there anything i am missing? the truck screams with any throttle but i am starting to grow tired of wondering if it's going to shut off at the stop lights... it never does but it teases me.
 

SY2455

70's Veteran
Re: hunting idle

#2875 said:
i have been working on this problem for a while now and thought i might see what you guys have to offer. basically my truck idles shitty after warmup. here is what i know:

1 leakdown check was good on all 6
2 boost leak check good, am leaking a little around the throttle shaft but not enough to cause a problem plus the tb is new, vacuum is about 17.5-18 at idle
3 a/f mixture is perfect datalogged on the dyno (ultimate chipped (vortec, 412, 50#ers))
4 valve timing is perfect, cam is on standard tooth, not adv or ret.
5 spark timing is perfect
6 i set the idle screw using a procedure i found here. unplug iac, connect pins, blah blah you guys know the drill
7 motor is fresh, i have all new sensors (no egr) multiple spark box, hot coil, ngks gapped to about 32

is there anything i am missing? the truck screams with any throttle but i am starting to grow tired of wondering if it's going to shut off at the stop lights... it never does but it teases me.

This is going to sound stupid, But did you check all vacuum lines,Timing, and IAC?
 

SBNova

New member
Re: hunting idle

I read a post a long time ago about tuning a vette with a hunting idle, that it helped to manually adjust the idle higher, giving the ECM/IAC less work to do, and less possible chance of having a low idle. The ECM wont be able to shut down the idle speed below the manual idle speed. Reportedly, this helped on a cammed engine, which I notied you posted a cam swap.
 

Don W.

Stab it and steer it
Re: hunting idle

Just FYI, in the Sy manual for rough, unstable or incorrect idle the first item is MAP sensor. After that all the usual stuff, bad grounds, ign, ect. One other item caught my eye; EGR. If you have one and it's leaking that would be a problem.
 

93TyGuy

Boost Freak
Re: hunting idle

You might check your Throttle Position Sensor...Notorious for hunting for an idle.
 

#2875

built, not bought
Re: hunting idle

i have a couple of map sensors and actually a couple of tp sensors as well. plus i can check all that with my scan tool. nevertheless i will triple check everything.
 

Don W.

Stab it and steer it
Re: hunting idle

Don't forget to check the EGR valve, assuming you haven't blocked it.
 

#2875

built, not bought
Re: hunting idle

alright i changed tps and maps with old ones no change. turned the idle screw up still no change. and i don't have egr. my only other symptom is the vacuum bounces 15-18 when it's hunting which may be a effect of the idle moving but i think it's the cause. one other thing it idles fine when the engine is cooler. still stumped.
 

Don W.

Stab it and steer it
Re: hunting idle

Electronic Spark Control (knocksensor) is listed in the manual as a cause for rough idle. Never changed one, heard that it's a fun job. I suppose you could disconnect it and try it, that will throw a code but it might help. Another thought since it seems to be heat related would be the ign module.
 
Last edited:
Top