Innovative LC-1 issue

Hey all,

Lookin for some advice on this one... Installed the LC-1 and got it all wired up but it's not working even close to correct... It either flashes 7.4 or the AFR is all the way up to 22.5 and won't come down... Did the free air calibration on it like it says... Wired it up like it says to. Connected the yellow output to the old o2 narrowband input on the ecm and tagged the old o2 ground to the same grounding point as the blue and white wires, and the brown is feeding the gauge... Tunerpro is picking up an o2 voltage in the ALDL but it stays around the 450-530 region an never changes... I played with it till I was pissed off and called it a night... Any suggestions? :dunno:
 

TYTILIDIE

METH HEAD
Re: Innovative LC-1 issue

Hey all,

Lookin for some advice on this one... Installed the LC-1 and got it all wired up but it's not working even close to correct... It either flashes 7.4 or the AFR is all the way up to 22.5 and won't come down... Did the free air calibration on it like it says... Wired it up like it says to. Connected the yellow output to the old o2 narrowband input on the ecm and tagged the old o2 ground to the same grounding point as the blue and white wires, and the brown is feeding the gauge... Tunerpro is picking up an o2 voltage in the ALDL but it stays around the 450-530 region an never changes... I played with it till I was pissed off and called it a night... Any suggestions? :dunno:

Did you program it with log works? What gauge did you get? What are you running for a chip?
 

syclone rider

New member
Re: Innovative LC-1 issue

Man i had the same problem at first and the way they tell you to wire it up is really wrong go to the search up there and type in what you have for the title of yours and its by me. Tytilidie gave me the right diagram in the thread.
 

syclone rider

New member
Re: Innovative LC-1 issue

Oh yeah do not run it again without removing the wideband sensor from the downpipe or it will jack the sensor up quicker than you think it would.That is until you get it wired up right.
 
Re: Innovative LC-1 issue

Did you check the ground offset? With the LC-1 have to do this and there is a setting in the software to adjust it. After that it should be accurate.
 
Re: Innovative LC-1 issue

Did you program it with log works? What gauge did you get? What are you running for a chip?

I did program the cable with the LM programmer. As of now I have the yellow wire emulating narrowband and is hooked into the stock o2 pin at the ECM and the ground for it is grounded with the white and blue wires from the LC-1. The brown is hooked to the gauge and is providing wideband. Turn the IGN on and the LED will start to blink then blink faster then solid like it should... The gauge, even after free air calibration when installed ALWAYS shows right around 21.0 with the truck OFF, start it up and the gauge will start to jump around in the neighborhood of 12.6-13.8 for about 2 minutes or so then the gauge will just flash 7.4 and the led light blinks off and on.... Turn the IGN off wait about a minute and start the car again works again.... :dunno: :banghead:
 

turbodig

Active member
Re: Innovative LC-1 issue

I had similar issues with one locally.... reload the firmware in the LC-1 and cycle power.

Also, I had to finally give up on one of the analog outputs and wire the other one into the ECM.
Once I did that, (and reprogrammed it accordingly) it matched up with the innovate gauge and worked fine.
 
Re: Innovative LC-1 issue

I had similar issues with one locally.... reload the firmware in the LC-1 and cycle power.

Also, I had to finally give up on one of the analog outputs and wire the other one into the ECM.
Once I did that, (and reprogrammed it accordingly) it matched up with the innovate gauge and worked fine.

Thanks Dig! I tried uploading the firmware to the LC once BUT didn't power cycle afterward. I will try that tonight after work! As it was I had the Yellow programmed to simulate narrow band because I was running $58 at the time of installation and wanted to make sure it would give a representative voltage reading through the ALDL. I think I'm just gonna go home tonight, load up the $59 .xdf and starter bin and go that route now that I have the necessary equipment. I looked up a thread someone had posted to TYTILIDIE about the DB gauge and calibrating the .bin using the nonlinear table for the AEM gauge and flagging it in lieu of the Innovative... Gonna try that as well! Thanks for the info!
 
Re: Innovative LC-1 issue

I did program the cable with the LM programmer. As of now I have the yellow wire emulating narrowband and is hooked into the stock o2 pin at the ECM and the ground for it is grounded with the white and blue wires from the LC-1. The brown is hooked to the gauge and is providing wideband. Turn the IGN on and the LED will start to blink then blink faster then solid like it should... The gauge, even after free air calibration when installed ALWAYS shows right around 21.0 with the truck OFF, start it up and the gauge will start to jump around in the neighborhood of 12.6-13.8 for about 2 minutes or so then the gauge will just flash 7.4 and the led light blinks off and on.... Turn the IGN off wait about a minute and start the car again works again.... :dunno: :banghead:

Everything sounds fine until the 7.4 comes up. 20.9 when it not running is correct and 12.6-13.8 is afr during warmup.

The LED light blinking on and off must signal some type of error. Just my assumption.
 
Top