Just bought the Phil long Chip

juicehead9

93 Typhoon # 0973
Re: Just bought the Phil long Chip

Phil
I would like the V5 chip I will pm you soon when i get the $$$ I want to go this rout ($35 if you just want me to burn one and send it to you and you keep both. You will get a little better fuel mileage with the V5.) How will i get better fuel mileage does it have a fuel saving mode?
__________________
 

akwilks

Mr. Keith
Re: Just bought the Phil long Chip

I installed the v5 50 chip and I am getting excessive kr and my engine temps rise if I accelerate hard enough...My engine is stock with 8:1 pistons...my fp is set at 42psi and just had replaced the spark plugs with ur6s...should my engine run hot with this setup? I do have a hi flow fuel pump and msd ignition....I also dont have a cat but have a garret turbo with an external wg...I run about 15# of boost on average with occasional sprints of 17#s....I have removed the chip for now since I dont know whats going on with it...is there something I should be doing that I missed as far as using this chip? kr gets as high as 12*. I have been running 91 octane so far and maybe thats the issue but right now I am clueless...
 

Turbo6

10.20@131.8
Re: Just bought the Phil long Chip

akwilks said:
I installed the v5 50 chip and I am getting excessive kr and my engine temps rise if I accelerate hard enough...My engine is stock with 8:1 pistons...my fp is set at 42psi and just had replaced the spark plugs with ur6s...should my engine run hot with this setup? I do have a hi flow fuel pump and msd ignition....I also dont have a cat but have a garret turbo with an external wg...I run about 15# of boost on average with occasional sprints of 17#s....I have removed the chip for now since I dont know whats going on with it...is there something I should be doing that I missed as far as using this chip? kr gets as high as 12*. I have been running 91 octane so far and maybe thats the issue but right now I am clueless...

91 octane wont cut it especially if your engine is running hot!
 

Turbo6

10.20@131.8
Re: Just bought the Phil long Chip

juicehead9 said:
Phil
I would like the V5 chip I will pm you soon when i get the $$$ I want to go this rout ($35 if you just want me to burn one and send it to you and you keep both. You will get a little better fuel mileage with the V5.) How will i get better fuel mileage does it have a fuel saving mode?
__________________

It has slightly leaner settings at idle and under light load.
 

akwilks

Mr. Keith
Re: Just bought the Phil long Chip

Today I put 10gal of race fuel (107 octane) in my truck. I installed the phil long chip again and at 42psi fuel pressure the truck wouldnt idle well and eventually stalls...I bumped up the fuel enough to keep the engine idling but part throttle the truck stumbles...bumped up the fuel some more to relieve the stumble and decided to put a scan tool on the truck...the chip doesnt read the O2 sensor properly only showing .004v at idle...under load, it barely reads enough voltage for a normal reading at idle.....putting boost to the truck I was seeing about 6*kr....not too bad in relation to what I was seeing before....this was at setting 2 on the 5v 50 chip....I adjusted the chip to setting A and knock retard was at 3* before things started to get wierd....under load, the ecm would stop sending data and so I could only see what was happening for about 20 seconds....its like it takes a dump but the truck still runs....also, from a roll, if I give it half throttle or more, the truck bogs down for a second, I get a abs, brake, and cel light momentarily, they go out then the truck takes off...again, I dont have these problems with my other 2bar chip but seem to have bad luck with the three bar chips..Phil if your out there, I really could use some help here....I cant seem to run your chip in my truck...my other chip reads my O2 properly and doesnt give me the driveability issues I am seeing with your chip. My email is akw1@rap.midco.net if you would like to respond to this. I plan to call Turbotune to try to establish an equitable solution to this....If I can, I will try to catch someone with a dm so I can send you a file as to whats going on....
 

Turbo6

10.20@131.8
Re: Just bought the Phil long Chip

akwilks said:
Today I put 10gal of race fuel (107 octane) in my truck. I installed the phil long chip again and at 42psi fuel pressure the truck wouldnt idle well and eventually stalls...I bumped up the fuel enough to keep the engine idling but part throttle the truck stumbles...bumped up the fuel some more to relieve the stumble and decided to put a scan tool on the truck...the chip doesnt read the O2 sensor properly only showing .004v at idle...under load, it barely reads enough voltage for a normal reading at idle.....putting boost to the truck I was seeing about 6*kr....not too bad in relation to what I was seeing before....this was at setting 2 on the 5v 50 chip....I adjusted the chip to setting A and knock retard was at 3* before things started to get wierd....under load, the ecm would stop sending data and so I could only see what was happening for about 20 seconds....its like it takes a dump but the truck still runs....also, from a roll, if I give it half throttle or more, the truck bogs down for a second, I get a abs, brake, and cel light momentarily, they go out then the truck takes off...again, I dont have these problems with my other 2bar chip but seem to have bad luck with the three bar chips..Phil if your out there, I really could use some help here....I cant seem to run your chip in my truck...my other chip reads my O2 properly and doesnt give me the driveability issues I am seeing with your chip. My email is akw1@rap.midco.net if you would like to respond to this. I plan to call Turbotune to try to establish an equitable solution to this....If I can, I will try to catch someone with a dm so I can send you a file as to whats going on....


I am not sure what the problem could be beacuse I have a TON of people running that chip without any problems at all. Make sure you FP gauge is reading correctly. Try 50 psi if you need to but 45 it what the chip is designed around. Your motor is stock right? The fuel you put in it wasnt oxygenated was it?
 

TheNeek

this is my serious face
Re: Just bought the Phil long Chip

Way off topic... But this thread certifies in my mind that Phil is an ECM pimp. If I wasn't buying a house soon I would be on top of the stock injector chip in a heart beat. Gotta take care of the little stuff before I go putting upgrades on the truck though.
 

akwilks

Mr. Keith
Re: Just bought the Phil long Chip

I'm not trying to difficult here I merely stating that I have compatibility issues...I bought my truck and can only go with what the previous owner told me....I had the new engine built so I know what I have internally but everything else I dont have the experience to verify...I was told I have 50# inj and it was verified that the injectors are not stock...I verified the ecm, I dont know why I have issues but I do...characteristically, I dont get the same information using Freescan with your chip as I do with the one that came with the truck...I understand the chips are different however some things should stay the same...feedback from the O2 for example is completely different between your chip and 2 chips I have ran in my truck( the one it came with and a 3bar custom chip I had borrowed).
Like I said, I am not trying to be difficult. I'm not passing judgement on the chip or its quality, I am just stating that it seems I just cant run it in my truck for whatever reason...Thats all...I dont have a reputable shop that can tell me whats going on nor do I have the expertise to understand either...I am going thru my truck this weekend from grounds to connectors....everything..If I cant get this to work I will have to consider the alternative....
I really like the chip...it definitely wakes my truck up and the difference is very noticeable...it just comes with other issues I cant identify that makes it undesirable for me......
 
Top