Knock Battles!!!!!

johnboy89

Member
This is more of a continuation from this thread:
http://www.syty.net/forums/showthread.php?t=79275

Have spent quite a bit of time trying to battle my knock issue myself!!!! Rob has been a big help trying to get my knock under control also. Thank You!!!!

I've changed the fueling F29X and made some timing changes, but nothing has really reduced the knock. Currently the timing table is less than stock and truck is very flat up top??????

Sometimes the knock is better after a tune change, then a couple of days later it's back, very frustrating!!!!!

I'm at the point where I feel I need to either run Torco or start spraying alky with stock boost levels????

I believe it's real, but have never heard it with a max of around 9 deg. is what I saw. Few times could hear a slight pinging sound up around 7-9 deg.

Thoughts, suggestions much appreciated :)

Datamaster_12_11.jpg
[/IMG]
 

RealFastV6

@jb_and_his_coffee
Re: Knock Battles!!!!!

Every DM file I've seen has this "on", don't think it means much?????

You're right- my understanding of that flag was backwards. Bypass means its bypassing the ignition module and is being controlled by the ecu, not the other way around. I never noticed that on my DM logs.

I can't imagine you're really knocking with 10 degrees of advance, stock boost, and 900mv o2s but you'll need to post the whole log.

Eta: Just read the other thread didn't realize you put heads on the truck.
 

johnboy89

Member
Re: Knock Battles!!!!!

Let me summarize what I have done so far:

1) New Walbro Fuel Pump with Hot Wire Kit.

2) Checked Fuel PSI to ensure it's rising with boost and it is.

3) NGK Plugs gapped @ 0.030. Checked plugs, but have no clue what to look for?????

4) Added a 1/2 gallon of xylene, no change!!

Things I'm going to try:

1) Put two gallons of Xylene in and see if knock is reduced.

2) Check compression as engine block was milled and heads might have been at some point.

3) Connect wideband into ECM.

Thanx :D
 

Beavis

Still plays with trucks
Re: Knock Battles!!!!!

heat shields, trans lines, loose exhaust anything that can rattle agianst anything and make noise.
 

Petesgn

Member
Re: Knock Battles!!!!!

Possible that you outer ring on the balancer moved and you have more initial advance that you think ?
 

SYCLONE#1531

'MOFOFAST
Re: Knock Battles!!!!!

Try some of the torco accelerator. I know it might not be the fix. It should though help eliminate some of the knock! This stough is no joke!!

torco.jpg
 

johnboy89

Member
Re: Knock Battles!!!!!

Possible that you outer ring on the balancer moved and you have more initial advance that you think ?

Almost positive when I put the engine together I checked this??

Have double checked base timing and it!s fine.
 

vmack

New member
Re: Knock Battles!!!!!

Is the knock sensor torqued correctly? (looked at the old post u said u think)
Is it a Delco? correct prt #? Any damage to plug or wire?
 

johnboy89

Member
Re: Knock Battles!!!!!

Is the knock sensor torqued correctly? (looked at the old post u said u think)
Is it a Delco? correct prt #? Any damage to plug or wire?

Pulled it out awhile back and re-installed to correct torque spec.

Correct part and no damage to wire.
 

johnboy89

Member
Re: Knock Battles!!!!!

One thing I forgot to mention is that the there is some piston slap when cold and knock is greater then!

Every DM run that I've done the knock follows boost so appears to be real, but to prove it I will add some xylene.
 

Matt

Active member
Just a shot in the dark but is your intercooler system working properly, no kinked lines dead pump etc
 

vmack

New member
Re: Knock Battles!!!!!

Pulled it out awhile back and re-installed to correct torque spec.

Correct part and no damage to wire.

I would like to knowhow that works out. How about could it be a rpm thing and not boost? If so I would think it is a vibration somewere causing it, i.e. piston slap maybe loose mounts. get a rachet strap in there somewere if u can to pull the engine tight to rule out mounts.
 

vmack

New member
Re: Knock Battles!!!!!

Pulled it out awhile back and re-installed to correct torque spec.

Correct part and no damage to wire.

I would like to knowhow that works out. How about could it be a rpm thing and not boost? If so I would think it is a vibration somewere causing it, i.e. piston slap maybe loose mounts. get a rachet strap in there somewere if u can to pull the engine tight to rule out mounts.
 

johnboy89

Member
Re: Knock Battles!!!!!

UPDATE

Added two gallons of Xylene to 3/4 tank of Shell 93.

Did two runs and KR wasn't much better:

This run was with around stock timing:

DM_2.jpg
[/IMG]

This run with about 3-4 deg. more timing:

DM_3.jpg
[/IMG]

Took the plugs out and some appear to have some aluminum specs on the porcelain, which indicates KR correct?? Electrodes look fine though????

Next on the list:
* Install bung and wideband O2
* Install colder plug UR6
* New knock Sensor (already did this)

Thoughts???

Thanx:)
 

It's just a six

Super Member
Re: Knock Battles!!!!!

Post some pics of your plugs.

Really need to install your wideband, the narrow band is very, very slow.

Colder plugs should help some.

What T-stat are you using? 180? Could try a 160

Do you have a C.A.I., cold air intake?

Do a compression check to see what your cranking compression is.

EGR is disconnected?
 

johnboy89

Member
Re: Knock Battles!!!!!

Post some pics of your plugs.

Really need to install your wideband, the narrow band is very, very slow.

Colder plugs should help some.

What T-stat are you using? 180? Could try a 160

Do you have a C.A.I., cold air intake?

Do a compression check to see what your cranking compression is.

EGR is disconnected?

Wideband will be in this week, not going to do any more test runs until it's in.

I've tried to take pics of the plugs before, but they don't come out very well!!!!! Not all plugs show "speckles", but #3 was the worst and was loose when I took it out????

Running a 180 t-stat, I've actually ran 160 before, but the piston slap get's worse.

EGR is disconnected with factory air intake.
 

It's just a six

Super Member
Re: Knock Battles!!!!!

I would install the colder plugs also., It won't hurt it.:tup:

So when you ran a 160 T-stat & piston slap was worse, did it show up with more knock retard also?
 

TurboTYPHOON

New member
Re: Knock Battles!!!!!

Do the compression check I was fight a KR issue that turned out to be broken piston rings. Part throttle- no knock; Full throttle- lots of audible knock. turned out the 5 of the 6 secondary piston rings were broken. :town:
 
Top