L35's or LB4's

HopnDude

I B Derpin.
Re: L35's or LB4's

I'm not sure. I've got a guy who specializes in GN 3.8's and SyTy 4.3's. He's fitted me up a 98 Block w/ 91 Sy internals w/ KB Low compression Pistons....So I don't know....But the heads that we're stock, he did some machine work to the ports to clean the castings....The heads are supposed to flow pretty good!....

I'll post pic's of the heads (if I get a chance) to show the port/pocket work!

464259_10150710757639910_515344909_9213333_24981775_o.jpg


475259_10150710758829910_515344909_9213339_191704666_o.jpg


476538_10150710759279910_515344909_9213341_642252036_o.jpg


And the intake that's gonna feed them cylinders under pressure!

209896_10150157401924910_515344909_6422640_5929171_o.jpg


My first time trying to post pic's on here, we'll see if it works, or if I'm just a huge failure!....::::pre facepalm::::....

I'll be doing the build shortly next month after I get back from Honduras w/ the ARMY....I'll post pic's up, but this 94 S10 is about to be a SERIOUS bastard child!....
 

HopnDude

I B Derpin.
Re: L35's or LB4's

Meh...here's a few more pic's of my bastard child....

317334_10150389315479910_515344909_8166891_561894968_n.jpg

The 8.5" rear end, still needs shortened.

387236_10150451734109910_515344909_8378472_760358657_n.jpg

The parts pile when it started, alot of it is in the engine build already!

And this is the current setup that's bout to go bye bye!
26005_337787464909_515344909_3397424_2601915_n.jpg
 

HopnDude

I B Derpin.
Re: L35's or LB4's

But back to the question on heads....wasn't there a 18 degree 4.3 head produced for a while?!
 

It's just a six

Super Member
Re: L35's or LB4's

My friend has this intake on his 2001 V-6 GMC Extreeme, ext cab Blower pushing some boost through it.;)
pics073.jpg


I believe it is one of three ever made.
I some other pics he sent me somewhere on my comp.
. I think they were done in Austrlia?
 

HopnDude

I B Derpin.
Re: L35's or LB4's

My friend has this intake on his 2001 V-6 GMC Extreeme, ext cab Blower pushing some boost through it.;)
pics073.jpg


I believe it is one of three ever made.
I some other pics he sent me somewhere on my comp.
. I think they were done in Austrlia?

say's "GM Performance Parts RAM JET" on the top?!....hmm....def a sweet find!....
 

It's just a six

Super Member
Re: L35's or LB4's

say's "GM Performance Parts RAM JET" on the top?!....hmm....def a sweet find!....

It was made originally for a SBC (RAMJET), but was cut up & welded back together to fit our V-6's.
Only 3 were ever made is what I was told.
Anybody else ever seen one?
 

MoJo

New member
Re: L35's or LB4's

Can you just install screw in studs & standard push rods (1986 - 1991 LB4, ZR9 cam.) & adjust them regardless of which cam you are using?

Unfortunately, valve train geometry is complicated for the part - time shade tree mechanic. This information applies assuming your block deck height, head deck height and valve stem length is stock.. Changes in those parameters will also have an effect on the valve train geometry.

If you use full roller narrow body rocker arms, you MUST drill out the 10mm threads in the heads and tap the hole for 7/16"-14 BigSerts and use ARP 134-7101 rocker studs. The ARP 100-7201 will bolt in without a TimeSert because they have 10mm base threads, but you must use stock stamped steel rocker arms because the 100-7201 studs are too short for full roller rocker arms and poly locks.

If you feel like must use some sort of roller rocker arm with L35 heads, the alternative to full roller aluminum rocker arms are the Comp Cams 1417-12 self-aligning "roller tip" steel rocker arms. They will work with the easily installed ARP 100-7201 bolt in rocker studs and they do not require the use of poly-locks. If you use those rocker arms and rocker studs, the lifter pre load will be fully adjustable and use the lock nuts furnished with the rocker arms. With the ARP 100-7201 rocker studs, you can also use your stock rocker arms, stock lifters, push rods and any camshaft.

The installation of the ARP 134-7101 rocker studs is required only if you want to use full roller aluminum rocker arms and poly locks.
 
Last edited:

SY2455

70's Veteran
Re: L35's or LB4's

HopnDude, Your heads are the newer Vortec Heads, not L35 and they should flow really well.
 
Top