MAP vs IAT

SBNova

New member
I decided to stop my tuning a few weeks ago pending my fuel pump install. Now that its in, and working nicely, I am ready to get back into it. Ive got some questions about this table, that just doesnt seem right. When I look at the MAP vs IAT table in TunerPro, why do the entries seem so erratic?

In the screen shot, if I had an IAT of 121 degrees, why is it that I *need* to pull 4.92 degrees out ONLY at 75 kpa?? Yet it pulls out 1.76 degrees everywhere else at the same IAT?? It seems that it should be removing a little more at higher IAT's, and the table should be alot smoother. Is TunerPro deciphering this wrong or is it really this way? Is there a reason its this way??
MAPvsIATpicture.jpg
 

JSM

Active member
Re: MAP vs IAT

The real answer is your one of the few that even know that table exists. GM didn't spend a lot if any time totally working out our ecm tune. So you will find a lot of odd things in our ecm, tables there not used at all or not to full extent.

The #'s you see are left over from GM code, very few tuners even change this table. Guessing due to the if it aint broke dont fix, or I didn't know it was there reasoning.

If you are running meth injection this table could be VERY valuable.
 

skwayb

NWSTP
Re: MAP vs IAT

Yah that table is messed up. The ECU I based my 3Bar version off has a ton of errors in it. I am currently going back through and fixing as many errors as I can find. I will post a new XDF here in a week or so once I get done going through every thing.

To fix the table now go in and make these changes to it in the TunerPro

General Tab make these changes.
Populate by ROW
output type floating point

On the Row Tab make these changes
Row = 5
Row Units = Degrees C
Row Label type = Integer
Make these changes to the table lables
Row Label
1 0
2 24
3 49
4 80
5 100

For Degrees F is it
Row Label
1 32
2 74
3 121
4 176
5 212

On the column tab make these changes
Columns = 9
Column Units = kPa
Column Label Type = integer

Make these changes to the Column lables
Column 1 2 3 4 5 6 7 8 9
0 25 50 75 100 125 125 150 175 200 (2 BAR)

For 3 Bar
Column 1 2 3 4 5 6 7 8 9
0 37 75 112 150 187 225 262 300 (3 BAR)

On the Conversion tab change the formula to this
0.351563 * X + 0.00

That should correct it. I will post a picture of it.

f3_table.jpg


For 3 Bar
f3_table_3bar.jpg
 
Last edited:

SBNova

New member
Re: MAP vs IAT

Thanks for the input. So those numbers are correct? If thats the way GM left it, then there is alot to gain in driveability and knock reduction right there. I agree that meth/alc users would greatly benefit using this table too.
 

JSM

Active member
Re: MAP vs IAT

Forgot about the row -vs- column thing Paul mentioned.

I will be honest in the short time I have seen you learn tuning, you are picking up things quickly. I like it. Glad to see some others not scared to play and ask questions.
 

sytyguy

Moderated User
Re: MAP vs IAT

I always redo this table anyhow (in conjunction with reworking F1 & F80.) What I generally do with a new tune is this:

- Zero out the timing advance/retard in F80 and F4. This makes the overall spark advance a more "clear" number.
- Get F1 nailed down. Start with idle (but it usually doesn't require much work) and move to cruise. Look for proper numbers and smooth operation (you want no hesitations or dead spots). Then move to WOT. I get at about 50-60 mph in third gear and do a smooth roll into boost, gradually flooring it, ending around 80-90 mph. Watch timing/retard numbers - I usu tune safely, looking for 13-16 deg advance (no knock) from stockish heads.
- Add timing back into F80 (usually around 2-3 deg for a street tune.)
- Add timing/retard into F4. I have it pulling timing (1-3 deg) above 120 degF and adding timing (1-3 deg) below 80 degF.
- Go out and retest.

* - For alky I usually have it adding more timing at lower temps and pulling more at higher (higher temps can indicate low alky or a failed system - better safe than sorry.)

** - I like to think of F80 as a race gas map as it gives the ability to add timing only in PE mode (usu above 4 psi.) So, make a pass with street tune, and then add timing as necessary to aid performance.

Hood
 

SBNova

New member
Re: MAP vs IAT

Paul, I think I m ade my last reply at the same time you posted how to correct the table.

I made the changes you said, but noticed the table only alters timing when not under boost. Is that the way its supposed to be? The timing values have changed drastically with the changes you suggested. They read better now, but it would be nicer if the code allowed timing changes at >100kpa vs. IAT.
 

SBNova

New member
Re: MAP vs IAT

Hey I dont have an "F80" field. Is it "PE contribution to spark advance" your talking about??
 

skwayb

NWSTP
Re: MAP vs IAT

Well the hack I am looking at, that is how it was labeled. The hack may not be correct. This is one of the tables I needed to investigate more on the test bench. If you want, put the old values in the columns (0, 25, 50,75, etc.)

I had my 3 bar rescaled to 300 kpa. Not sure why I changed the table back..... oh yah.... I looked at RBobs 58RR14.xdf and that is how he had it. I think it makes more sense to have it be in boost. I don't think the hack I had is 100% correct for this table. Let me repost what is should be...
 

skwayb

NWSTP
Re: MAP vs IAT

F80 is in there.. might not be labeled F80. The new XDF will have all the F lables.


Look at address 0311. The table name is
PE CONTRIBUTION TO SPARK ADVANCE - DEG. VS NTRPMX
 

SBNova

New member
Re: MAP vs IAT

Yeah thats the table I thought it was (F80).

You guys are awesome with this code stuff. I only wish I knew more about this stuff to really contribute.
 

skwayb

NWSTP
Re: MAP vs IAT

I think I am going to revisit the formula for this table. Other info I looked at looks like it should be.

0.351563 * X + -21.8

And the lables of the table look like they should be

2 bar
0 12.5 25 37.5 50 62.5 75 87.5 100

3 bar
0 25 50 75 100 125 150 175 200

Look at the notes here on nwstp.com

http://www.nwstp.com/forum/chiptable.asp

I need to do some more research on this to make sure it is correct.

Any one have info on the correct setup of this table.....?
 

skwayb

NWSTP
Re: MAP vs IAT

Ok see that the label is....F3_TABLE Spark Advance Adjustment vs ADMAT1K
Deg. vs Deg. C & kPa Boost


hmm.. if it is suppose to be for boost then numbers or the kPa numbers when in boost. any change at the 0 mark would change everything when in vaccum. I think it is just confusing the way the table is set up.

It really should be labeled.

2bar
100 112.5 125 137.5 150 162.5 175 187.5 200 (kPa)

3bar
100 125 150 175 200 225 250 275 300 (kPa)

Since 100kpa in the chip is 0 PSI. Makes sense now.

How would you guys like it set up?
 
Re: MAP vs IAT

Well i just made the above changes to my table as wll and all the numbers went from negative to something that looks decent.

Heres what my new values changed too.
16.52 16.52 16.52 16.52 16.52 16.52 16.52 16.52 16.52

19.34 19.34 19.34 19.34 19.34 19.34 19.34 19.34 19.34

20.74 20.74 20.74 20.74 20.74 20.74 20.74 20.74 20.74

21.45 21.45 21.45 21.45 21.45 21.45 21.45 21.45 21.45

24.61 24.61 22.85 22.85 22.85 22.85 22.85 22.85 22.85
 

SBNova

New member
Re: MAP vs IAT

I just plugged in the changes in the fomula, and it seems decent. Not what HotRodV6 posted, but numbers varying from 1.76 - 7 degrees pulled (negative). I left it from 0-200kpa, but it does seem to make more sense at 100-200kpa, only changing with boost. HotRodV6's numbers would make quite a change for IAT's. I think the other is probably more likely correct. Here is what I have now.


newIATvskpa.jpg
 

skwayb

NWSTP
Re: MAP vs IAT

Are you running 2 bar or 3 bar?

If 2 bar then you should be running these values

2 bar
0 12.5 25 37.5 50 62.5 75 87.5 100 (boost in kPa)


In psi
0, 1.8, 3.6, 5.4, 7.2, 9, 10.8, 12.6, 14.5

The table needs to be labeled

Spark Advance Adj. -vs- Manifold Temp & kPa Boost 2 Bar

The kPa values are for when in boost. A 2 bar chip goes from 0-200kpa. Where 0 - 100 kPa are in Vaccum and 100 - 200 kPa in boost. But this table is only for boost kPa, so the values listed have had 100 kPa removed from them. Normally a table like this would be labeled
100 112.5 125 137.5 150 162.5 175 187.5 200 but they decided to have it be the kPa value for the boost level since 200kpa when calculated comes out to 29psi which we know is incorrect.

I hope that all makes sense.

As far as the data in the table, that all comes from the conversion formula that I am looking into. If this table is an adder than the -21.8 in the formula might need to remain. If it is the actual timing you will run at X temp then it would need to be removed. When would you run negative timing? Jury is still out on this since I haven't had a lot of time to look into at work.
 

SBNova

New member
Re: MAP vs IAT

Yeah I am gonna change the lables to go from 100-200 kpa. I am used to reading my whole vacuum to boost range as 0-200 kpa, so seeing it go from 100-200 will click with me as being all boost. I understand what your saying though.
 

skwayb

NWSTP
Re: MAP vs IAT

skwayb said:
On the Conversion tab change the formula to this
0.351563 * X + 0.00

Ok this is a wrong formula. This table is an add/subtracter from your timing value. The correct formula should be
0.351563 * X + -21.8

The negative numbers in the table are how many degrees of timing it is pulling from your spark at that temp. You should update your formula to match this one.
 
Last edited:

SBNova

New member
Re: MAP vs IAT

Yeah Ive got the correct formula in there now. This is what I have;

IATvsMAPversion3.jpg


It seems right to me, the values and all. My columns are labeled as all boost >100kpa. I am used to reading the "Mass Air Pressure (calculated 2 bar from a 1 bar variable)" table when I log, so the column labels will sync in my head this way.

Thanks for straightening this out for me!
 
Top