MAP vs IAT

skwayb

NWSTP
Re: MAP vs IAT

No problem. If you see anything else that looks whacky or have a question let me know. I trying to get the XDF 100%. Sometimes I look at some of this stuff a million times and it looks right cause I am always looking at it. Another set of eyes always helps.
 
Re: MAP vs IAT

well i changed my conversion to the one above and rescaled mine to read 100-200 and heres what my new table reads

-5.28 -5.28 -5.28 -5.28 -5.28 -5.28 -5.28 -5.28 -5.28
-2.46 -2.46 -2.46 -2.46 -2.46 -2.46 -2.46 -2.46 -2.46
-1.06 -1.06 -1.06 -1.06 -1.06 -1.06 -1.06 -1.06 -1.06
-0.35 -0.35 -0.35 -0.35 -0.35 -0.35 -0.35 -0.35 -0.35
2.81 2.81 1.05 1.05 1.05 1.05 1.05 1.05 1.05 1.05


Not sure why i dont get the same numbers, but i guess it looks right.
 

SBNova

New member
Re: MAP vs IAT

HotRodV6- Do you have an aftermarket chip by chance?? I checked every "stock" syty bin I have (all four), and they all read the same. Except for the first two entries at 00 Celcius, your table looks reasonable too. Mine varies advance with temp and boost and yours just seems to vary with temp. You have much less pulled at colder temps than I do too. Interesting.... I plan to pull some timing at higher temps, to keep me from knocking on these hot Florida days, and keep al little more in it for the cool nights and evenings...
 
Re: MAP vs IAT

SBNova said:
HotRodV6- Do you have an aftermarket chip by chance?? I checked every "stock" syty bin I have (all four), and they all read the same. Except for the first two entries at 00 Celcius, your table looks reasonable too. Mine varies advance with temp and boost and yours just seems to vary with temp. You have much less pulled at colder temps than I do too. Interesting.... I plan to pull some timing at higher temps, to keep me from knocking on these hot Florida days, and keep al little more in it for the cool nights and evenings...


Well no chip, just the autoprom with a T3-20 bin file that ive been tweaking here and there.

Ive noticed that when at the track on my first run after letting the truck sit and cool off and icing doen the IC i dont get any knock, but if i come back around for a second run with only a few minutes of cool down, b8ut still low temps on both the engine and IC i start to get some knock at the top end of the track when my IAT's get up there, so i will be playing with this some more once i get the thing running again.

I also have a 3 bar map.


Ive also got mine set to read out in Degrees F, would that change anything???
 

skwayb

NWSTP
Re: MAP vs IAT

HotRodV6 said:
Well no chip, just the autoprom with a T3-20 bin file that ive been tweaking here and there.

What version of the Ultimate chip are you running? My table is from a T3-22 version 6 bin. I have been custom tuning it to my Ty but I haven't touched that table yet.

HotRodV6 said:
Ive also got mine set to read out in Degrees F, would that change anything???

Shouldn't hurt anything. It is just the label for the table so as long as you did the C -> F conversion correctly on the numbers you netered, it shouldn't matter. You have to remember that if you decide to link ALDL values to the table you need Calculated 3 Bar Map mapped to the X Axis and MAT in degrees F to Y Axis.
 
Top