Moates adapters...

vortecfiero

New member
Ive been looking at the various adapters that moates has and it suddenly dawned on me (finally!)
with these adapters you do not have to cut your origonal chip off the carrier !
I didn't catch that at first and I was wondering why bother with them and I didn't see
anything about that in any of the articles or on the Moats page

G1 appears to be a basic adapter, to use the knock sens and a different prom, not using the stock prom on the carrier
G3 appears to allow switching between bins (how many?)
EX works in conjuction with G3 and is a remote switch and display (once again how many bins?)

have I got this correct ?

also if I have already cut the prom off, it seems these adapters wil still work
 

sytyguy

Moderated User
Correct.

Using a 29F040, you can burn 32 bins @ 16kb. Only 16 are usuable however as the switch only accomodates 16 positions. You'll have to load the 16 bins you want use in the upper half IIRC. I just mirror them the same (same 16 in upper half as lower half). This pretty much makes it the same as a 27C2001 or 27C020, except the 29F040 is flashable.

FWIW, If the jumpers (J2) are in the 29C256 position, the adapter is in "pass through" mode, which is what you'd want to use for the Romulator.

Having your EPROM cut off the stock memcal should make no difference as the stock memcal is only used for ESC circuitry and the onboard chip overrides the stock EPROM anyways.

If I made a mistake, someone please correct me.

HTHs

Hood
 

Turbo6

10.20@131.8
I use the moates for switching bins. I like the GP3 kit with the EX. It runs around $100 and you get the adapter, ZIF, 29F040 flash chip and remote switcher. You can switch up to 16 bins. The EX remote reads 0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F. I like using GMECM edit to stack the bins.

You will need to remove the blue cover on your chip for it to fit without modding the ECU case. Remember to use the RF filter that comes with the remote kit. It goes between the cable and the adaptor. I love mine and never had a problem.
 

sytyguy

Moderated User
Turbo6 said:
You will need to remove the blue cover on your chip for it to fit without modding the ECU case.

While this isn't entirely true, there is a chance you may want to remove the blue cover to get the chip into position. The picture below shows mine fitting without any mods......just requires some funky tilting/angling to get the chip down in there.

http://www.georgiasyty.com/tuning/images/adapter7.jpg

I'm not nit-picking, just don't want anyone hacking their case with the mentality that it won't fit prior to actually trying it.

Hood
 

Sy769

Donating Member
Or if you only want single bin capability the Hypertech chip carrier can be used. Remove the hypertech eprom and ad a lever style ZIF socket. Works well.

It is the only good use for anything syty related from Hypertech.
 

kwick6

Donating Member
sytyguy said:
Turbo6 said:
You will need to remove the blue cover on your chip for it to fit without modding the ECU case.

While this isn't entirely true, there is a chance you may want to remove the blue cover to get the chip into position. The picture below shows mine fitting without any mods......just requires some funky tilting/angling to get the chip down in there.

http://www.georgiasyty.com/tuning/images/adapter7.jpg

I'm not nit-picking, just don't want anyone hacking their case with the mentality that it won't fit prior to actually trying it.

Hood

Yep, what he said. It will fit, just not easily...:D

I have the GP3, but have just used a 29C256 so far. Didn't want to mess around stacking bins, since I'd be only changing one thing at a time anyway for now.
 

BillC

New member
FYI, Promgrammer also now has the capability to stack bins. It can also separate stacked bins, too.

Go ahead and ask if you want comments/input about how well it works (I'm a little biased, so I'll refrain :D ).
 

vortecfiero

New member
BillC said:
FYI, Promgrammer also now has the capability to stack bins. It can also separate stacked bins, too.

Go ahead and ask if you want comments/input about how well it works (I'm a little biased, so I'll refrain :D ).

does any body know (If not Bill) if a stacked bin file will run through the Romulator
 

sytyguy

Moderated User
There would be no need to attempt to run a stacked bin through the Romulator. Remember that the Romulator emulates a bin file....and as such, you load the bin you need to edit and tune away. Running a 16kb bin file on a SyTy ecm? The Romulator emulates that 16kb bin file. Emulating on '95 Silverado ($OD)? The Romulator will emulate as a 64kb bin file.

You'll hafta put the Moates G3 adapter on 29C256 jumper setting to get the Romulator to work, which will make the adapter act in "pass through" mode, and a stacked bin would be pointless. The Romulator will emulate up to 27C512 eproms (64kb), so it probably could handle a stacked bin, but if you want to look at other programs on the fly with the Romulator, just load another bin.

HTHs

Michael
 

BillC

New member
vortecfiero said:
BillC said:
FYI, Promgrammer also now has the capability to stack bins. It can also separate stacked bins, too.

does any body know (If not Bill) if a stacked bin file will run through the Romulator
Stacking bins refers to taking several bins and combining them into one file for use in a larger-than-stock chip. This is very useful for switchable setups, like the Ultimate Chip or the appropriate Moates adapter & switch setup. It allows you to run different programs without swapping chips, by switching between the various memory offsets (start reading at 0x0000, start at 0x4000, start at 0x8000, etc.). The stacking feature in Promgrammer (and in GMECM Edit) makes it easier for the user to stack bins without using a hex editor.

If you set up Romulator correctly (set it to emulate the correct size chip), there's no problem sending a stacked bin to it. However, unless you use a switch on the adapter board (like the U.C. control box or the Moates switch), you'll only see the bin in the top location. So, there really isn't much need to send a stacked bin to ROM emulator. As sytyguy pointed out, if you wanted to try a different bin, you could just send the different bin to the emulator.
 

vortecfiero

New member
BillC said:
vortecfiero said:
BillC said:
FYI, Promgrammer also now has the capability to stack bins. It can also separate stacked bins, too.

does any body know (If not Bill) if a stacked bin file will run through the Romulator
Stacking bins refers to taking several bins and combining them into one file for use in a larger-than-stock chip. This is very useful for switchable setups, like the Ultimate Chip or the appropriate Moates adapter & switch setup. It allows you to run different programs without swapping chips, by switching between the various memory offsets (start reading at 0x0000, start at 0x4000, start at 0x8000, etc.). The stacking feature in Promgrammer (and in GMECM Edit) makes it easier for the user to stack bins without using a hex editor.

If you set up Romulator correctly (set it to emulate the correct size chip), there's no problem sending a stacked bin to it. However, unless you use a switch on the adapter board (like the U.C. control box or the Moates switch), you'll only see the bin in the top location. So, there really isn't much need to send a stacked bin to ROM emulator. As sytyguy pointed out, if you wanted to try a different bin, you could just send the different bin to the emulator.

I did understand that thanks

I was considering that it might be safer to switch between stacked bins
rather than sending and resending files (with my luck with computers)

either way, this could be way too much fun !
 

vortecfiero

New member
Santa came a little early this year !
just got my Moates GP3 package
It is a slick piece. Looks like he has changed the set up from the pics
(it's the one with the zif socket)
the board has a different reciever socket (easier to use) than the G1
and has attached the zif to the reciever rather than just soldering the
zif to the board. Which probably saves the costs of keeping 2 sets of boards in stock
 
Top