My cheap BOV install question

HighPerformanceTrucks

Lift & Shift Specialist
I just installed a Mitsubishi BOV as it is a very good OEM BOV and it only cost me $25.00 at the salvage yard.

My question is where have most of you attached you vacuum line to? Manifold? Tee into vacuum source?

I just found a plug on the firewall side of the throttle body, anyone use this for a vacuum source?

Thanks.

Adam Auerbach
Sy #2419
 

Loeryder

New member
I tapped mine off the front of the plenum.
You want it to get boost so don't go behind any of the check valves.

And don't tap into the FP/MAP lines as it will make the MAP less accurate and could effect FP rising with boost if a leak develops at the BOV.

HtHs
 

Hu Ryde

Donating Member
Adam, Make sure it's a metal bov, and make sure it's crushed or it will leak boost around 17psi. Search some DSM boards for instructions about crushing to hold more boost.
 

SY2932

Administrator
Or if it doesn't work satisfactorily, you can spend the money and get a HKS SS BOV like Jesse, myself and several others are using...

Mike Campbell
 

myclone

Donating Member
Ive got one of these BOVs that a DSM fellow gave me a while back. Instead of crushing it can the metal top be drilled and poss tapped for a bolt to tighten the spring down or is there nothing above the spring for the screw to contact. Dont wanna cut this one up to find out(its brand new).

TIA
 

HighPerformanceTrucks

Lift & Shift Specialist
Blow off valve not working right yet.

Blow off valve not working right yet.

I tapped into the nipple on the throttle body just to the right of the IAC valve and it must be a bad pressure source as the blow off valve is not releasing.

Anyone know if this fittiing is too close to the throttle butterfly to be useful?

Adam
 

Hu Ryde

Donating Member
Is that before or after the TB blades? If it's on the manifold side of the blades it's ok. You need a source of manifold pressure.
 

HighPerformanceTrucks

Lift & Shift Specialist
Hu Ryde said:
Is that before or after the TB blades? If it's on the manifold side of the blades it's ok. You need a source of manifold pressure.

I have a feeling that line is a water line to keep fuel injected motors from freezing up.

I'll probably just tap into the FP regulator line.

Adam
 

Ian Turgeon

Cascading Inspiration
ivanko barbell said:
Hu Ryde said:
Is that before or after the TB blades? If it's on the manifold side of the blades it's ok. You need a source of manifold pressure.

I have a feeling that line is a water line to keep fuel injected motors from freezing up.

I'll probably just tap into the FP regulator line.

Adam

dork, use the one at the front of the intake manifold. put a T there, and run it to your bov. Dont steal the fpr or map's vac. any fitting on the TB is going to stink for a vac source.
 

HighPerformanceTrucks

Lift & Shift Specialist
SyTyArchives said:
ivanko barbell said:
Hu Ryde said:
Is that before or after the TB blades? If it's on the manifold side of the blades it's ok. You need a source of manifold pressure.

I have a feeling that line is a water line to keep fuel injected motors from freezing up.

I'll probably just tap into the FP regulator line.

Adam

dork, use the one at the front of the intake manifold. put a T there, and run it to your bov. Dont steal the fpr or map's vac. any fitting on the TB is going to stink for a vac source.

Yeah, I'm finally starting to sound stupid after all I've been through this weekend on my truck. I'm frazzled. I'll look for that vacuum line you're speaking of.

Adam
 

Makaveli

New member
I've got the name of the guy who did the last GP on the HKS's and price now is still around $200 depending on flange...price includes shipping...
 

just a 6

R.I.P MyClone
Well the 1g DSM (91-94) BOV holds good up to about 22 psi, the 2G DSM BOV are the weak ones, leaks freqently at higher boost. Make sure you got a 1G BOV and you be ok.



Hu Ryde said:
Adam, Make sure it's a metal bov, and make sure it's crushed or it will leak boost around 17psi. Search some DSM boards for instructions about crushing to hold more boost.
 

Matthew Little

New member
bov

bov

I ran one of these on my eclipse for several years and seem to work great, but after getting a Greddy I noticed a big difference in the bosst, the 1g bov was leaking after 14lbs, My buddy ran one on his GN, but had trouble with it staying open and then slamming shut. I run a blitz on my ty on a hard up pipe I made. I got my vac. from the port on the firewall side of the tb(the top port not the lower) I just used a step down to go from the 1/2? to what went into the blitz. I have some pics so e-mail if you want to see them.
Thanks Ty#0194
 

Matthew Little

New member
bov

bov

I ran one of these on my eclipse for several years and seem to work great, but after getting a Greddy I noticed a big difference in the bosst, the 1g bov was leaking after 14lbs, My buddy ran one on his GN, but had trouble with it staying open and then slamming shut. I run a blitz on my ty on a hard up pipe I made. I got my vac. from the port on the firewall side of the tb(the top port not the lower) I just used a step down to go from the 1/2? to what went into the blitz. I have some pics so e-mail if you want to see them.
Thanks Ty#0194
 
Top