my sy won't start

Xtrempickup

All turbo All the time
My truck died driving home a while back. I parked it and forgot about it for a while. Prior to it dieing it intermittently wouldn't want to start. The one good day it did I drove it and for about 40 min it was great. Then it died coasting to a stop. Truck cranks strong, but no start. Fast forward 2 years til today. I check for fuel at the rail and Its there. I checked resistance of the coil itself, checks out OK according to the video I watched for checking a coil on YouTube. I'm leaning toward it could be the HEI on the distributor. I had another Chevy truck die suddenly and act the same as the SY is doing and it was the hei. Does this sound likely? Is the hei for the SY a standard item I can get from a parts store or GM? Suggestions? Advice?
 
Last edited:

JSPsyclone

Donating Member
Re: my sy won't start

It could possible be the control module under the cap. Usually when these go out it will turn over but won't start. Check the cap and rotor as well.
 

Jimmy

Banned
Re: my sy won't start

Does the tach jump up and down when you crank it? If not it's probably the ignition module.
 

Xtrempickup

All turbo All the time
Re: my sy won't start

Tach does not move when cranking. I hooked up my timing light and cranked it since I was trying to verify spark without pulling a plug out and the wire and the timing light doesn't light up at all when cranking leading me to believe I don't have spark. I guess I'll get a ICM and a distributor pickup and a new cap and rotor and go from there
 

Jimmy

Banned
Re: my sy won't start

Tach does not move when cranking. I hooked up my timing light and cranked it since I was trying to verify spark without pulling a plug out and the wire and the timing light doesn't light up at all when cranking leading me to believe I don't have spark. I guess I'll get a ICM and a distributor pickup and a new cap and rotor and go from there

Just try an ignition module first. It's that or the dist.
 

Xtrempickup

All turbo All the time
Re: my sy won't start

OK, I'll start there. Thanks. Will update with progress after I get and change that
 

atkonkler

Is this your bush?
Re: my sy won't start

Bring it to autozone....oreillys and or napa....they will test it for free....but if the tach doesn't flutter when you turn it over I'll put money on a ign.control module....:2cents:
 

Sportmachines

Active member
Re: my sy won't start

I second the ICM, but make sure to start with the simple stuff first. Check the ecm fuses. Check the fuse behind the alternator. See if you're getting spark at the coil, then ICM. HTH
 

SY2932

Administrator
Re: my sy won't start

X3 on the ignition module.

wol_error.gif
This image has been resized. Click this bar to view the full image. The original image is sized 640x480.
IMG_1831.sized.jpg


"If the chip is installed correctly, and you definitely have both spark and fuel pressure, your ignition module is dead. A bad ignition module won't generate a reference pulse preventing the injectors from firing. Part number is 1048-2827 (located under your distributor cap, BTW). Some auto chain stores can test to confirm it it's good or bad."

If you get the ignition module tested, be sure to have it tested *several* times even if it passes the first test. I have seen ones pass the first test only to fail more and more parameters as they are tested and heat up... If you have one of those problem children, it will be ok in your truck until it heats up and then you're going to be dead in the water until it cools back off. The chain stores; AutoZone, Advance Auto, etc., carry the Wells number DR140 but my experience with them is they don't last as long as the OEM ones.
 

Xtrempickup

All turbo All the time
Re: my sy won't start

What fuses are we talking about for the ecu? I checked the coil for ohms with an ohm meter, I couldn't do anything more. I picked up an ICM, a distributor pickup and a cap and rotor. If things are easy to access I can do them after 5 today when I get home
 
Last edited:

Jimmy

Banned
Re: my sy won't start

What fuses are we talking about for the ecu? I checked the coil for ohms with an ohm meter, I couldn't do anything more. I picked up an ICM, a distributor pickup and a cap and rotor. If things are easy to access I can do them after 5 today when I get home

ECM a and b fuses.Thats not your problem though so it doesn't even matter

If the B fuse is blown,the fuel pump won't work.If the a fuse is blown,nothing will work.You have fuel pressure so those fuses are fine.
 

Xtrempickup

All turbo All the time
Re: my sy won't start

I don't know how much pressure I have, but there is fuel in the rail. I changed out the ICM. No change. I did check all those fuses and they are good. I need to get a tester for the fuel rail cause it doesn't spray me if I press in the schraeder valve, it sorta just dribbles out. Not sure if there should be a lot of pressure on the rail from just cranking. I'm gonna change out the distributor pickup tomorrow.
 

TeeTopZ

Member
Re: my sy won't start

You need about 43 pounds at the rail with the vac line disconnected. Get a FP testing gauge from Autozone and see what you have. It sounds like a bad pump to me
 

Xtrempickup

All turbo All the time
Re: my sy won't start

My original thought from the time it happened was bad fuel pump and have dreaded doing it hoping for something easier. Will know more tomorrow.
 

Damian

Member
Re: my sy won't start

To test the fuel pump, there is a stray wire behind the intercooler. Run a wire from the battery to that wire and that will turn the fuel pump on, then you can easily see if you have fuel pressure.
 

SY2932

Administrator
Re: my sy won't start

I don't know how much pressure I have, but there is fuel in the rail. I changed out the ICM. No change. I did check all those fuses and they are good. I need to get a tester for the fuel rail cause it doesn't spray me if I press in the schraeder valve, it sorta just dribbles out. Not sure if there should be a lot of pressure on the rail from just cranking. I'm gonna change out the distributor pickup tomorrow.

Sounds like you might have a fuel issue. However, low pressure at the fuel rail after cranking it and getting out of the truck and testing it could simply be a bad check valve in the fuel pump. I have this issue on my truck with it not holding pressure, it will drop as soon as I shut the truck off, but I have a Walbo 255 that is 15 years old. However, it does exactly what its supposed to do when it's running. My fuel pressure increases one pound per one pound of boost. This is how I test the fuel pressure in sytys:

IMG_0846.sized.jpg

"Applying 12 volts to fuel pump test connector to troubleshoot fuel pump or set fuel pressure with vacuum line still connected and motor off (note fuse for safety).

If you end up having to replace the fuel pump, it's not that bad of a job on a syclone. I did a how to write up a couple of years ago that will walk you through it.
 

Xtrempickup

All turbo All the time
Re: my sy won't start

Don't know what it was but its running. Sprayed ether in the intake it popped. After that its been starting without any issues. I'm stumped. Pump primes and runs. Still no gauge to check the actual pressure at the rail
 

Xtrempickup

All turbo All the time
Re: my sy won't start

Ok, let it sit 2 hrs while I did the wiper motor and its dead as a door nail again. This fuel pump has got to be on the way out. Maybe I have overlooked a clogged fuel filter, will try that tomorrow.
 
Last edited:
Re: my sy won't start

had similar no start problem turned out to be Moates adapter was loose, check that if you have one. I changed the pump before finding that was the issue,pulled the bed off to change it. good luck
 
Top