Need help fixing gauges

thewumpus99

Donating Member
Just bought a '92 Typhoon last night. My first one! A zillion small things wrong with it, including the gauges.

First, the oil gauge never moves from zero. It does light up at night. Any ideas where to start looking?

Second, the top gauge (air/fuel mixture I think it is, with the rectangular LED's) just goes nuts the whole time I drive. Dozens of LED's light up back and forth the whole time even at a steady speed on a flat stretch. When I take my foot off the gas entirely, all LED's go out. Is this normal? If not, any diagnostic tips? Also, is this gauge supposed to be backlit at night like the other two nearby gauges?

Still trying to track down some repair manuals, but until then I'm winging it. Thanks in advance!
 

George Blake

DONATING MEMBER
Re: Need help fixing gauges

Your oil gauge has flipped all the way around and is on the bottom of the peg. Common problem.

The other gauge you are describing is not a stock gauge. Sounds like an aftermarket gauge. Someone else might be able to help you there.
 

Syclone0565

CustomMulticades.com
Re: Need help fixing gauges

Sounds like the second gauge you have is a air/fuel ratio gauge. Nice one to have actually and no its not stock. Flipping all over the place it actually normal :p
 

thewumpus99

Donating Member
Re: Need help fixing gauges

OK, time to ask some stupid questions.

Stupid Question #1:
This is a photo of the cluster of gauges I'm talking about. Is this whole thing aftermarket? Or just the individual gauges inside the cluster? They're surrounded my molded plastic the same color as the rest of the interior.

Stupid Question #2:
Here is that flatlined oil gauge. It doesn't look pegged from the outside?

Stupid Question #3:
This photo shows a fuel pressure gauge that is mounted on my hood. It also bounces back and forth like crazy during steady driving. I assume the fact that this equipment was installed probably means there is some way to tune fuel pressure from inside the car? (I don't see any obvious control for this.) Or is it just for looks?

Stupid Question #4:
This momentary switch is below my cigarette lighter. The text is worn off, and pressing it produces no obvious effects. Any idea what it is? (Wish the car had come with the Typhoon owner's manual supplement!)

Stupid Question #5:
This 2-way switch is to the left of the air vent just below the steering column. As can be seen in the photo, when it is in the bottom position, an orange facet can be seen. Is this stock? If so, what's it do?

Stupid Question #6:
This is the air/fuel mixture gauge I was talking about. Anybody know how these are supposed to work?

I realize these are pretty remedial questions. Thanks for being patient with me :)
 

Black Knight

I Glow Therefore I am
Re: Need help fixing gauges

1. Yes whole thing is aftermarket.
2.It's not pegged from the outside, it's probably not connected more research is required.
3.Not sure if you can adjust from in the vehical, but fuel pressure is something we really try to keep an eye on, but I wouldn't have mounted on my hood.
4.Don't know it doesn't look like it's in there correct.
5.Not a stock switch you will have to test this one yourself, possibly a i/c on off or a tcc lockup.
6.I think they do bounce around, but more research is needed on this also i.e. where it's connected and if it has all the required equipment.
HTH
 

Syclone0565

CustomMulticades.com
Re: Need help fixing gauges

Nothing you showed in the pics is stock.

The 3 pod gauge holder you show in the picture is just there to hold the additional gauges. The 2 switches you will have to figure out. I bet one of them is a converter lock-up though. One may be your fog lights if the fog light switch is missing or broken.
The oil gauge is probably just not hooked up any more. You can trace wires and lines to see though. While you are in there you can check the 2 switches wires and see where they go also. These modifications that were made to your truck are actually common modes about everyone makes when they upgrade their truck. All but the fuel pressure gauge on the hood :lol: . I am sure it was put there due to the fact it was not an electronic gauge and they did not want the raw fuel line in the truck. You can buy an isolator though and move it inside.

Hope this helps a little
Good luck with the truck. :p
 

Syclone0565

CustomMulticades.com
Re: Need help fixing gauges

The Air/Fuel Ratio gauge you have or AFR gauge will not be a very useful tuning tool aside from sustained WOT tuning. The problem is that the aftermarket AFR gauges use the factory O2 sensor for it's mixture information. The O2 sensor that is on our sytys were never designed to constantly read the air fuel ratio and give an accurate output (that is what a Wide Band O2 sensor does)... It was designed to act like an umpire and tell the engine "rich" or "lean" so that the engine can adjust the fuel trim accordingly. The idea is that the O2 sensor will oscillate back and forth from rich to lean and log what are called 'cross counts' which indicate that the air fuel ratio has gone from rich to lean or vice versa (crossed ~.450 mv). The ECM needs to see a decent amount of cross counts to be happy. If the O2 sensor stays rich or lean too much (ie not enough cross counts), the ECM will flag a DTC for the rich or lean condition that exists (thus the common O2 sensor rich or lean codes when it is actually some other componant that has failed, causing the improper mixture).

So by understanding what the job of the factory O2 sensor is, you can see why the AFR gauges that rely on it for input are not very useful tuning tools at anything but WOT. At WOT the mixture will stay a steady state of rich (if everything is working properly) and you can tune how rich the engine runs at WOT with Fuel pressure regulator settings and EPROM tuning. The idea (way to make the best power) is to run it as lean as posssible without detonating or pre-igniting the mixture....

Hope that all helps a bit
Good Luck...
 

Black Knight

I Glow Therefore I am
Re: Need help fixing gauges

Hey John do you know how often the O2 sensor checks that info? Are we talking like every second or 10 times a second? Just wondering
 

Syclone0565

CustomMulticades.com
Re: Need help fixing gauges

Black Knight said:
Hey John do you know how often the O2 sensor checks that info? Are we talking like every second or 10 times a second? Just wondering

I used to watch mine and it was constantly moving all over the place. I would say it does it several times a second. But I am not for sure on that one. Sorry
 

SY2455

70's Veteran
Re: Need help fixing gauges

#4 looks like a rear wiper switch, not installed right. Where are the Typhoon Owner's at?
 

thewumpus99

Donating Member
Re: Need help fixing gauges

I've also got a Rear Wiper switch; it's a rocker-style with a momentary push for wash, and not just a rectangular momentary push-button like the one pictured in #4.

What I do NOT have is a rear wiper! Guess either the switch or the back is non-original. There isn't one there, nor is there a mounting hole for one. I live on a muddy road, so a rear wiper is a must. From the photos you guys have posted, it looks like the wiper connects through the rear glass. Is this right? If so, can I grab wiper-equipped rear glass from a junkyard Jimmy, or was this rear glass/spoiler Typhoon-only?

Thanks for all the help guys!
 

Daman

Member
Re: Need help fixing gauges

#4 is the Rear Hatch switch used to open the rear glass from the inside. When you press it, you should hear the actuator in the tailgate trying to pop the rear glass open.
 

thewumpus99

Donating Member
Re: Need help fixing gauges

Good call Daman! It wasn't doing anything, so I checked out the solenoid. Someone had cut the solenoid supply wire inside the hatch! Upon reconnecting it, I discovered why - it was shorted to 12VDC somewhere. Checking the switch, both sides had 12VDC on them, and the switch itself checked out. Tracing the black wire downstream from the switch... and someone had spliced in a green +12VDC wire under the dash for some bizarre reason. Unspliced it, and everything is working great now.

Oh, and #5 goes to a white/flourescent orange wire that goes into the "security system" box (not even sure if this thing works), and a black wire (presumably ground?) How does one "arm" the stock security system? Probably worth reconnecting it I suppose.

There does not seem to be a torque converter clutch lockup switch - will have to add that, along with a taillight/license plate lamp cutoff switch :)
 
Top