No Lamda signal

TurboTony

Active member
So what did you find at terminal C?

And no, do not rely on the scan tool for this test, that comes later.


Tony
 

BadTy

Member
@ Tony

The ECM dont receive a signal of the O2 sensor!
The ground on the downpipe i`ts OK.

I`ts possible that in the "open loop" the O2 signal stays always at 442 mV?

Roland
 

TurboTony

Active member
Okay, I'll ask again

what did you measure at terminal C of the o2 sensor plug, key on, engine off.

Ignore the friggen laptop for a second and go measure it.


Tony
 

helfmann

New member
@BadTy
What doe NO SIGNAL mean? No power flow at all or unreliable signal?
Check with a peeper. If there is nothing coming through the wire at all check wire (have fun digging through the car). Did you check the freaking connectors to the ECM yet. Some of these cables are rather small and like to break.
Advice:
Swap ECM and check
If The other ECM has the same issues ---> cable!

M@
 

BadTy

Member
Hi Guys!

The power flow from the plug (pin C) to the ECM its OK! I have checket this with a peeper.


The truck is up to Monday evning by a friend for install a shaved door kit.
Monday I will check that what Tony says: Key on, engine off and measure at pin E14 on the ECM if I receive a signal or not!
Until Monday I can make unfortunately nothing.

Thanks for your assistance

Roland
 

TurboTony

Active member
I give up,

You haven't listened to a word i've said.

Go back and reread all the instructions and do exactly as I ask. Otherwise forget it.


Tony
 

BadTy

Member
OK OK OK!!


Sorry that I do not speak English. :( I translate everything by a online translator!!
I must word for word build up. So that I can understand, what is meant.
it is so already difficulty enough!
Here in Switzerland nobody can help me.

I ask for patience

Property again everything readed and stated that it was my error.

Tony, you means that I must switch on the key, but engine off. Than measure what I have on plug C!
All this without the scan tool. Only by a multimeter


Roland
 

helfmann

New member
@Turbo Tony
Sometimes it helps to make people think - LOL

@BadTy
Procedure (an overview):

0. Take a deep breath and smoke a cigarette, prepare the multimeter and don't hurt yourself with these sharp ends of the terminals.

1. Ignition on // Engine off
2. Measure directly at the C terminal wire which is supposed to submit values in a range from 0 - 1000 mV to the ECM.
Default should be in an area of 450 (as stated by BG and others).
After that, take the freaking wire diagram you have and check WHICH terminal delivers O2 readings to the ECM.

Check there, give the laptop to Sabina and let her play minesweeper on it

Go from there and you have success. I bet it's a broken wire at the ECM and/or missing or bad ECM and chassis ground.

M@

Btw nobody is complaining about your English just about the procedure
 

TurboTony

Active member
Tony, you means that I must switch on the key, but engine off. Than measure what I have on plug C!
All this without the scan tool. Only by a multimeter

Yes, do exactly that and post back with your results. Put the negative lead of the multimeter to the batteries ground terminal or some other known good ground.

Lets take this one step at a time.


Tony
 

BadTy

Member
Thanks for your patience!!!!


I`ts the first one, that i write in Englisch :)
Up to now I read from time to time a few lines in this forum.
I`ts difficile for me to read a long text AND understand everything. If it will somewhat write several people at the same time still more
with difficulty

I`m checked today the first one the 3. SyTy CD ROM about my problem. Owing to the pictures I understood, what is meant

Roland
 

BadTy

Member
I will come back to my problem of no O2 signal


I`m checked the connection from O2 sensor to ECM (purple cable). I`ts OK (0 Ohm)
If I measure the signal with a multimeter on Pin E14, the signal stays always at 0.88 V. If I disconect the purple cable on ECM and I measure on the purple cable comming from O2 sensor, the signal is OK. Changes from ca. 0.6 to 0.9 V up and down.
So the problem is, if the purple cable to ECM are connected, the lambda signal does not changes and rests always on 0.88 V. If I disconect the cable directly on ECM, the Signal works rightly.

Roland
 
Top