Open loop?

It's just a six

Super Member
I have been messing around w/the Moates autoprom w/no success as of yet.

So I reinstalled my ultimate chip & noticed my A/F ratios seem to be in open loop mode.

I warm the engine for several minutes & the idle A/F ratio is between 12.0-13.0, used to be around 13.9 - 14.6 range.

When I bring the engine RPM up to around 2000 RPM the A/F ratio goes a little leaner say around 12.8-13.6. range

Just wondering what would cause this?

The engine just seems to be in open loop mode.

Last time this happened was when I forgot to hook up the mapp sensor connector, but the A/F ratio was much richer, in the 10. something range.

I have not changed anything other than the moates G1 adaptor then switch back to the original ulitmate chip.

Would a bad O2 sensor cause this?

Any ideas, much appreciated.
Thank you.:tup:
 

BoostedSUV

Active member
Re: Open loop?

I'm pretty sure Ultimate chips run in open loop all the time. Pretty sure I read that once before. They adjust fuel and timing based on the map sensor and not the O2 I believe.

EDIT: just checked sytychips.com and I was correct. The ultimate chips run in open loop mode all the time
 

It's just a six

Super Member
Re: Open loop?

OK, well anyways, my A/F ratio is richer @ idle now & am wondering what could have made it do this?

As stated earlier, the idle A/F ratio was 13.9 - 14.6 range. All I changed back & forth a few times was change the ultimate chip & install the Moates G1 adaptor , then back to the ultimate chip.

Could an O2 sensor going bad make it idle richer by basically 1- 1.5 full point?

Or when an O2 sensor goes bad it just goes really rich @ idle?

Could not having the ultimate chip seated properly cause a rich condition @ idle?

Thanks
 

dgoodhue

BuSTeD 4.3
Re: Open loop?

The 50# ultimate chips were definitely open loop. I thought the stock injector ultimates were closed loop.

Our stock code $58 only has 2 long term (BLM) fueling adjustments, one at idle and one for the rest of the fueling table. To put that in perspective my outdate 86-89 Corvette 165 ECM code had 16 BLM's. Having only 2 doesn't allow for much adjustment. The O2 Sensor doesn't instantaneously change the fueling, it averages over a period of time and then is only able to adjust the whole fueling table. If you have rich and lean spots on VE fueling table, its not going to be able to compensate for those both of those areas. The plus side of this is if you have lean area (such as the transition to build boost), the ECM will not be able to correct that.
 

dgoodhue

BuSTeD 4.3
Re: Open loop?

What ultimate and injectors do you have? Having the chip not seat should be cause the truck to run bad all the time especially with a 3 bar maps it defaulting to limp home mode calibrated for stock injectors and 2 bar map.

Does it say close loop on the scan tool? Did you change the fuel pressure during this time? What does you stock O2 reading at idle, ideally it should be reading between 100-900 mV, but if your running 12-13.0:1 AFR, it will probably be reading in the 800mV range. Have you run leaded race fuel with either you WBO2 or stock O2 sensor? Does it smell rich after warming up at idle?
 

smeagol

Active member
Re: Open loop?

Stock injector cals were closed loop.

50# injector cals were open loop. The valet *might* have been closed loop (I believe I set it up as valet/emissions).

I found the open loop to be a much smoother operation, especially given the fact that the Syty cal only has 2 BLM as dgoodhue mentioned. Anyways, it *does* open you up to the possibility of running rich or lean in some situations, and if you are really out of touch or have problems, potentially rough running, fouling plugs etc.
 

It's just a six

Super Member
Re: Open loop?

What ultimate and injectors do you have? Having the chip not seat should be cause the truck to run bad all the time especially with a 3 bar maps it defaulting to limp home mode calibrated for stock injectors and 2 bar map.

Does it say close loop on the scan tool? Did you change the fuel pressure during this time? What does you stock O2 reading at idle, ideally it should be reading between 100-900 mV, but if your running 12-13.0:1 AFR, it will probably be reading in the 800mV range. Have you run leaded race fuel with either you WBO2 or stock O2 sensor? Does it smell rich after warming up at idle?

I have the old radar ultimate chip aprox year 2000. Made for stock injectors.

I have not driven the Sy since it seems too rich @ idle,maybe I should take it around the block a few times & see if it changes.

It seems to idle smooth,no misfireing, I have not used a scan tool on it I need to try & hook up tunerpro5 & see.

I had used race fuel one time a few gallons, but have since filled up the tank a few times w/unleaded.

The readings I am getting are from my LM1 & it does seem/smell a bit rich @ idle.

Thank you.:tup:
 

It's just a six

Super Member
Re: Open loop?

Update, I installed a new O2 sensor & ran it, idle A/F ratio was in the 10's & it smells rich.

Before this rich condition, after warm-up engine used to idle w/an A/F of 13.9 - 14.6 range.

I know before this problem,, you know when you start up the car & it is in cold start mode, engine idle is higher A/F ratio is kinda rich as not to stall the engine & A/F ratio is aprox 11.-12. something for a few minutes, then after a few minutes of warming up, your A/F ratio will go leaner until A/F ratio is running about 13.9-14-9 range & idleing.

Well, my Sy does not do this anymore, start it up, stays in the 10.1 range & stays there.
Is there a sensor telling the ECU that the engine is warmed up & telling the ECU to reduce the fuel delivery?

If so, what is that sensor, water temp sensor or??

Thanks.:tup:

Rick
 

smeagol

Active member
Re: Open loop?

Get a scan tool on there and it will give you better data as to what is happening. See dgoodhue's earlier questions.
 

It's just a six

Super Member
Re: Open loop?

Update,
I installed a remanufactured ECM P.N. 16198263.

I start it up & it runs a little leaner @ idle all warmed up, A/F ratio 14.6-14.9 approx , run the rpms to 2500 RPM & it is way lean 20.1, change ECM back to original, runs rich again @ idle 12.5- 13.9 , run it up to 2500 rpm stays around 14.7 .

Swap back newer ECM, idles to 13.9 bring the rpm up to 2500 A/F ratio is @ 16.0 too lean.

Was wondering if the circuit board may have some semi broken solder? Maybe from swaping out memcals too much, can this happen?
Any ideas?

Anyone have a good ECM I could use/buy , I need to smog the Sy.

Thanks:tup:

Rick
 

It's just a six

Super Member
Re: Open loop?

I have not changed anything but swap out memcals back & forth, this is when my problem started.

That is why I am thinking it has to do w/the ECM.


The truck ran perfect before I started messing w/the memcals.
 

WyoSyclone

Active member
Re: Open loop?

It's not unusual for these trucks to have a rich idle (especially when cold). When you put the stock ECM back in it how does it run when driving? Put everything back the way it was in the beginning, let the truck warm up (greater than 160 degrees), then see where the AFR's are.
 

It's just a six

Super Member
Re: Open loop?

Thanks guys,

With the stock ECM, it runs rich about 10.0-12.0 range & it loads up,but @ WOT, it runs fine after it clears out the fuel loaded plugs.

I am thinking about putting the stock memcal & 2 bar mapp sensor & see what happens also.
 

It's just a six

Super Member
Re: Open loop?

Update.
I picked up my friends Syclone ECM & tried it out.

Seems to be the same, I made sure the engine is up to temperature (only has a 160 T Stat) (Maybe too cool ?)

I tried the ultimate chip test , as follows idle A/F ratio 12.8 - 13.1 range
2500 RPM 14.7 - 15.1
Tried a different new 3 barr mapp sensor results the same.

I installed a custom 3 barr chip/memcal I got from Sean Morris idle was a tad richer but the 2500 RPM test result was the same 14.7 - 15.1

I installed just the stock 2 barr memcal & 2 bar mapp sensor results as follows: idle 13.9 - 14.4 @ idle
@ 2500 A/F ratio is way lean 17.0

Still confused with what is going on w/the truck.

I bought the tunner pro 5 but have yet to get it to work.

Could it be possible the engine is not hot enough for the 3 Barr set-up for the idle A/F ratios being too rich? They are fine @ 2500 RPM.

I think w/the stock 2 barr chip it might pass the smog test @ idle ,13.9 - 14.4 , but will fail @ the 2500 rpm test because of being too lean 17.0

I am pretty sure the w/the 3 barr set-up t will fail the smog test @ idle 12.8 - 13.4 but would pass @ the 2500 RPM test being 14.7 - 15.1 range.

So, as of now I tried all 3 ECMs w/all the same results from all 3, from swapping chips, memcals, 3 barr mapp sensors,then trying even all ECMs w/the 2Barr memcal & Mapp sensor.

Any possible solutions?
Sorry I do not have data master or tunner pro ,but am open to any suggestions.

Thanks guys.

Rick
 
Top